I've got VW UP 2018MY with battery discharge problem. I found that Central electric (09) and Can gateway (19) does not go into sleep mode. Even after few hours current meter show 0,150ma power consumption.
It's look like somebody have played with long coding.
Actual coding is:
62A02B0000010000000000D0688928D07940708D00CF0D280101000B0800 (30 Byte bornetz)
Can gateway:
001201
Anyone can help decode all bits? I'm using 24.7.1 VCDS but there is not full description for that unit.
Hello everyone, I purchased a Ford KUGA 2011 2.0 TDCI TXDA and I would like to ask you if there is someone which can provide me Service history by VIN - WF0RXXGCDRBE64404
Hello, I have 2 files stage 1 from 2 diferent tuners, I want to know which file is better performance and safer for car.
VW Passat 2020 2.0 TDI 150 HP stock DSG DQ381 all stock. Thank you all
hello, is there anyone who has done 801a immo off before, I read it with 16bit but I tried immo off but it didn't happen, is there immobox in this car? or is my method wrong? thanks advance
My e46 320d was tuned before more than years and it has, according dyno curves, 170hp.
But then we coudn't make more hp becaus there were some problems with the car.
At this moment I repared turbo, fuel injectors, vacuum lines and the car feels much more better.
As i know +/-200hp is the save limit for this motor.
So, maybe someone can help me, check the file and try increase hp to +/-200hp?
Bmw Hardware ID: 07793443
Bmw Software ID: 07788338
Bosch Hardware Number: 0281010565
Boch Software Number: 1037361858
Are EDC15VM+ VW Diesel ECU's interchangeable as long as they are coded/flashed correctly? I have a VW industrial 1.9l AVM with EDC15VM+ 038906012GS 0281011018 and cannot find a spare ECU with the GS suffix code. I do have two extra ECU's from a 2002 Golf that are 038906012FD 0281010653 . Can I reflash the Golf ECU to work on the industrial engine?
Hi all
I need a tested file to remove Immo from Fiat Stilo. No dash lights, no beeps.
Can you help me?
Ecu is a 5NF.T1
Attached the reading, both files.
Looking for tested solutions. Thank you in advance.
Hi, I'm asking for your advice. The lady only sent me the VIN code (WF06XXGCC6HD54782) if I can turn off the TPMS. Can someone tell me based on the VIN codes if it is possible to turn off Scanmatik orig. and FORScan in the Ford Focus (that's all I know) for this vehicle. Thank you very much
Hello, long time ago I made application to help me edit BCM2 module light functions, now I updated design and I would like to sell it for 10 Euros.
You can pay through Paypal or Revolut, other detail in Private message. Software activates and works on ONE computer.
Possible flag for Virus from antivirus, its all safe, no worry, you will have to trust on that one, cant figure out problem to fix it.
Just read 195 to 212 adaptation channels and insert in application, translate it, then you can change any function, brightness, lamp diagnostic, lamp types.
If I make Update, it will posted here and if application was activated it will work on same computer.
Always welcome to ask for new functionality or you saw some mistakes, I will change it and update it.
I know its many different ways to code these modules.
Example of use:
1. Connect to BCM2 (46 module)
2. Insert Security Access code: "16017"
3. Read Adaptation channel "195" (as example you get "14887" value)
4. Copy and Paste value to application "Edit Number" textbox and press "Insert"
5. Now can choose light function from drop box in "Function" section.
6. Change function from 7 to 3 and you removed TURN signal from function
Before: 14887 Right 29/127 Position, Brake, CH-LH, Turn Lights After: 14883Right 29/127 Position, Brake, CH-LH Lights
7. Now you can copy and paste new value to BCM2 Adaptation channel 195 and write it.
Sketch box - have button "Translate", it reads all line of sketch box and gives out information about channels functions in words.
TaiLight position -will change with side lights are, LEFT or RIGHT.
Functions with word CENTER are lights, that Instrument cluster will show without direction as "REVERSE LIGHT" not "RIGHT REVERSE LIGHT".
In some cars, logo/icon in instrument cluster will show that light in middle of rear end, not right or left corners.
You can turn off lamp Diagnostics by editing 191,192 adaptations channels values.
You can change lamp types, LED or HALOGEN by editing 181 adaptation channel value.
After you pay for application, send HWID to me and I will generate activation key for you, it will work ONLY on that computer. ONLY if you cant see HWID or something goes bad then inserting registration key in application with a PROOF, I will return your money.
If activation key was inserted and application said "BAD KEY!" the new button will show "COPY ERROR"
That button will copy error message and I will see what happened.
If you Reinstall Windows, same key should be working for that pc.
U2101:00-af and u2300:64-af 
![[Image: 16hjcr5n7W5qnAUBxp9572N5UuiI0xHn1]](https://lh3.googleusercontent.com/d/16hjcr5n7W5qnAUBxp9572N5UuiI0xHn1)
![[Image: 1WzGYvBoPfHheLG7LQpJbDpIWrdVH0jTr]](https://lh3.googleusercontent.com/d/1WzGYvBoPfHheLG7LQpJbDpIWrdVH0jTr)
![[Image: 1lvuRKSmH3HJroaqnoZsXJE9G4Aq_UVcZ]](https://lh3.googleusercontent.com/d/1lvuRKSmH3HJroaqnoZsXJE9G4Aq_UVcZ)
