Hello anyone can selling me software to change VIN on a BCM i tried reading the micro and editing the dump when i connect with witech shows absolutely nothing in the vin
hi
for clone opel astra g psg16 pump ...read pin and eprom with carprog and flash with MPPS and write eprom and flash in donor car pump?
is correct this procedure ?
i know anybody make this procedure and car start ...but i dont know if its correct
thnks
hi there member...am having an audi which i was able to disable immo in ecu after original was stolen..
car starts but gear not shift..i have bcm2 and dsg dumps which need sych
anyone that can assist me..
I have on dash this indicator and its filkering after ignition on and egine running
in car diagnostic zero errors
Anyone have idea what is it?
thx for any help
[font="MHH Font", Calibri, sans-serif]Hi ,please help with CAT OFF, fault P0141 (second lambda), after flashing E2 and test drive have warning light "car with wrench" and no faults.
[font="MHH Font", Calibri, sans-serif]Please help me with good solution? Ecu Simtec 76. Second lamda is delete. [/font][/font]
I set "BDEMODZU" to "1" and also "CWBDEMKO" to "1" in the hope that the car would go into HMM. But that doesn't seem to work. I suspect that the parameters (bits and bytes?) in the RAM need to be changed. With the DAMOS I can see the designation in the RAM, but I can't see any values that I can change. I think I'm missing the ADD-ON here.
EDIT: I would like the car to always run in HMM. Up to 4000rpm
Edit2: Or can someone tell me for a tip how I can drive with Lambda >1.0 in partial load up to 80% load? I'm also desperate about that. I've tried a lot, but I just can't get past Lambda 1.0. Anything < Lambda 1.0 is no problem.
I would like to drive from 1500 RPM - 4000 RPM up to ~80% load with Lambda 1.1 - 1.2. For a road trip or the city.
That solution would be the best.
Does anyone have the time and inclination to unlock the homogeneous lean (HMM) operating mode for me for a tip?
Hello every bmw enthusiast!
I need your help for this problem
Original is 256kb and donor is 512kb, I cant clone it.
Could you please help me to make it work?
I attached original files from cas3 and from donor cas3+.
Thank you very much!
I have a problem during the try to calibrate a Porsche 991 PDK. When I try to start the calibration with my piwis clone I get this error after the oil-temp is reached:
I'm currently in a project converting from x166 USA HALOGEN to X166 GLS look, with chinese parts.
And main problem is that according to seller i must conver from halogen to xenon and then fit "led gls" headlamps.
process is done, it seems working for the most part. except there is no low beam. When i activate with headlamp stalk high beams turns on with low beams together as it should. BUT no low beam.
First thought comes that coding is not complete. so I am looking for CBC and HLC166 codings for xenon headlamps PREFL GL x166. Ideally USA without ILS.
[color=var(--YLNNHc)]Hello i have try to read with Flex this ecu audi A3 edc17c74 ,i have id but fail to read password.[/color]
[color=var(--YLNNHc)]the support told me that the ecu had been modified previously and without the original reading the password cannot be extracted....any other solution to read this ecu? Other programmer read?[/color]
[font="MHH Font", Calibri, sans-serif]hi,[/font] [font="MHH Font", Calibri, sans-serif]someone can help me, i need car radio for vw polo in attached dump and label.[/font]
[font="MHH Font", Calibri, sans-serif]thank you regards.[/font]
![[Image: IMG-20241204-130906.jpg]](https://i.postimg.cc/Yjhqt3tY/IMG-20241204-130906.jpg)
