I've ordered VCX SE , is it worth it now to reinstall windows to install the XDOS instead of XPT. What are the benefits changing between the two software options?
What version are you recommending to install currently i have 09/23.
I own a business based in Australia and we currently convert U.S vehicles such as Dodge challenger ,Charger, Ram TRX , 2500, 3500, F250-F350 & we are looking at the 2024 Escalade.
The problem we face is the start up display on the Escalade shows the vehicle enter from the left ,then centre display and then flashes its lights followed by the Cadillac badge. (see link https://youtu.be/FOYfexyUh6c?si=tQdQs2jF1es0cfSv
the problem we face is that we need to swap the screens around to make it suit the RHD but in doing so the "movie" will be out of sync. What we need is to find either someone who can code this to work correctly or someone with the knowledge to teach us how to .
Hey all, we have lost the primary key from the Range Rover 2008 2.7l
We still have the 3 metal key cut that open the car and turn on the ignition, but we don't have any fob/controller
Is there a way to get an ebay key with the chip and code it as new with SDD, Diagzone, and Autel ? Or, Do I need to have one fully working key ? Thanks
Hi im having problem with dash on w222 , after reflash MCU D70F3525 with smok(jtag) dash works but doesnt show transmission position and engine rpm is 8000rpm but the car is 350cdi and have to be 6000rpm , i try over OBD with vediamo monaco but boot doesnt work, if someone have read same dash can share the files ?
Thanks in advance.
I tried to examine my intelligent drive unit (IDC213) in Xentry, IDC213, it made me install the module and now I'm receiving this error in Xentry that states "The control unit is not coded" for the IDC213 module (intelligent drive). I tried to load the module in DTS to clear the error but it shows DTC: P160400 0x160400, Das Steuerger? aet ist nicht codiert. (the control unit is not coded).
I'm also seeing a bunch of errors about no active blind spot, lane change, or steering assist when the car initially starts. Not sure how to get past these. If anyone knows it would be very helpful. Everything was working fine before this update. 2019 AMG GT53.
I have a 3.0 engine from a 2021 Sq5 that has a bent rod (car hydrolocked) . But its totally stuck, the engine will not rotate either clockwise or anticlockwise with plenty of force used on the crankshaft. Can anyone give me any tips how to remove this please? I'm going to remove the cap on the piston next to it tomorrow but don't think I can get to both bolts to remove the cap on the bent rod. Thanks in advance for any tips.
Hello everyone!
I own a Volkswagen Golf 5 GTD that has a Siemens PPD 1.2 engine control unit. I saw on the internet some videos where multimap was enabled on the car an the user could switch between maps using the cruise control stalker. Can anyone help me with that? Thank you!
Hi i've fitted PLA to my S3 and have control unit 5QA919298H however the unit is from a Seat and the 8V S3 displays the PLA on the MMI not the dash. I've seen online that the unit can be flashed with the 8V parameters however I can't seem to find the file online. I was hoping if someone had it would they be able to upload it so I can get the system working.
I was offered a 2007 BMW 328i for free to help me in my current situation. So this car was parked for about 8 months because the owner explained that they changed the battery to the car and it needed to be programmed in the ECU. In that time 3 people tried to make it work and the last one took the keys to it when leaving.
a
I figured drill the ignition,
-buy a new key with pin cylinder and change.
-Get software/hardware to bypass battery issue and
-unlock immo
Hopefully that works. I've programmed a hand full of Nissan, Hondas, and Ducatis But know nothing about BMW
What I need help with a cheap way to do all this
-Where to buy a cylinder and key for the Bmw preferred one with door cylinders also. But door isn't a priority
- some Info on the BMWs ECU and if I need to ans a link to a tutorial on how to program the battery, New key cylinder,
-How to turn off immo or is it cheaper to buy a new chipped key and virginize the ECU and program the new chip without buying expensive
-What programer is cheapest and easiest to use to program all the above ( I only have a FTDI KL-1 obd to USB programmer for my Ducati, not sure if that can be used to do any of the steps)
Any Help is greatly appreciated and links to where I can buy the products at a cheap price and preferred with stock in the USA but ok to get from China with fast delivery to save cash.
Thanks guys and really appreciate all the help everyone gives on these issues. There's no other site like this.
Hi! I'm looking for someone to modify BMW files. Now I have 2 cars in work, edc17 and MSV70. For edc17 I need SCR, DPF and EGR removed + tune (Car has downpipe, need something high performance) For MSV70 need performance tune (something around or under 300hp, catless headers, otherwise stock) Thanks! Willing to pay
Could anyone please provide me with the stock TCM calibration files for this 2015 Jeep Grand Cherokee. I believe the one I have is corrupted. VIN is 1C4RJFBT6FC215677. Thanks in advance!
