Guys,
Need some help with bench connection for this ECU.
In car I always have the code P056200 System Voltage Low and engine cranks but does not start...
So I thought let me connect it on the bench with known good power supply and check if the code is still permanent.
Reading trouble codes with Autocom still shows this error (beside all the other missing sensors off course) as permanent and I can not erase it.
Did I miss any connection (could not find a list with description of all pins) for GND or 12V to get rid of this P056200 error or is the ECU fried?
Your help is appreciated...
Seat Leon, 2019, DGTE 1.6L Diesel Engine.
Good day. Please help, maybe someone can tell the code of the ABS unit 58920-2W800 for the front drive. The car was brought from South Korea. The native one burned down and cannot be restored, but now it is installed on a car with a Santa Fe 3 but 4WD because I haven't found the native one yet. They say that this block can be recoded if I find the appropriate code from the same machine with such a block. Thank you in advance
Good evening. I have a 2005 wrangler that I'm trying to extract the pin from. From reading up the mask is a freescale/ motorola [font="MHH Font", Calibri, sans-serif]mc68hc08ab16a 0l72a chip has ( A2c00021380 0l72a)? But I have tried autel and vvdi prog. [/font]
[font="MHH Font", Calibri, sans-serif]None seem to read it , i have tried with capacitor removed and trace cut. Next will desolder mcu. [/font]
[font="MHH Font", Calibri, sans-serif]Just wonder if any has come across this issue before and if I'm using the correct mcu setting. [/font]
Hi, any one that can help do coding on a Volvo from 2007 the webasto heater is set to work when temperature is low to heat engine - need to change that to timer so it is heating the car cabin I read online it is possible
Hello people
Theres a Nissan Frontier 2023 with ADBlue system using SID321 and we need someone to reset the adb system
The adblue pump got broken and we changed it but the car does not understand it
It still says theres no ADBlue and the car doesnt work.
Its is possible to do? We are willing to pay for it.
Thanks
my m43 engine in my bmw e46 316i has a blown control unit,
I bought a new one and i need to upload vin and ews, immo,
I have the data from the old unit, but i don't know if i just need to upload the old data to the new unit or more steps are needed,
it's a low cost winter drift so as long as the ews, immo is knocked out i won't mind.
Anyone advise, I read somewhere that you need to unpair the chip (would that solve everything?).
Found few rail pressure limiters, and rail pressure maps, but can not find rail pressure sensor linearisation map, factory is 1800 bar new one is 2000bar.
Hello friends, I want to get started in the world of key programming. I'm from Spain, what machine do you recommend? Im508s is the most recognized here, is there any better?
Hi, m8s!
The problem is that the central locks stop working from remote control when the car goes asleep. If the car is locked, you must open it with metal key and remote control starts to work. If the car is opened, you must to open the door and again the remote control is working.
It looks like EIS is not working good. But there are no other problems with the car: there are no error codes, the car always starts, ESL works every time the key is in ignition switch.
Maybe somebody had the similar problem? What must I check first of all?
I can't check the live data in EIS because when the diagnostic interface is connected to the OBD, there is no problems with remote control. If works always.
Hello!
Would anyone be so kind as to share the flash file of the CLK W209 Rear SAM (SAMH)?
I'm looking specifically for the dump from a car equipped with a roller shade and an updated dash.
Hello everyone, I need help, a problem happened, when recording a dump to the dashboard via obd, a failure occurred and the dashboard stopped turning on and communicating. Before this, I repeatedly read and wrote this panel on the obd (added and removed options, etc.) everything was in order.
Apparently the data in the p or d flash has been corrupted. Does anyone have a dump from this shield?
shield number 94031 - further numbers are not important, the main thing is that it is diesel and restyling. solved.
hi team
Does anyone have a safe solution for this ecu?( Iveco 2003 2,3 95HP ) I tried several software programs with disconnecting the immobox but nothing worked
I've had 3 people mod file and no good.
EGR/DPF/ADBLUE OFF.
Still have CEL and transit has problems driving.
Attached is the link to Modded file and Stock (ORI)
Using Trasdata and My Genius Master.
Need solution with sensors unplugged.
