Hello, I have a Mercedes GLA 250e 2023 prefacelift and I want to code BCFA2 and PARKMAN213 and I cannot I have dts Monaco with projects files that I have coded two a250e w177 of 2021 in the past but when I am trying to code this one that it model year 2023 it says NRC=33, does anybody have project files that work with this year?
Have a brand new genuine 6154B with the wifi head 6154/5a, when trying to set up and scan for networks it does not do anything or find any networks? yet i put my old 6154 wifi head on my new interface and it finds the networks. Am i missing a setting for the newer type wifi head? or have i been unlucky with a brand new kit with the wifi head being faulty?
the car coming with error P1A5B00 cooling oil valve no basing setting .. and i can not do basing setting
The TCM dosen t work ..change in d but not drive.
Also I need full sw 8W2927155AN eprom+ micro
i read in TBs , if i have error P1A5B00, for this kind of mechatronic then i have option to replace mechatronic with new one .
i thing to do dtc off or to adapt immo data in other one with same software part number
i pay for solution .
ASAM/ODX File ID:EV_TCMDL382021
ASAM/ODX File Version:002027
Vw/Audi Part Number:8W2927155AN
Software Version:0001
Hardware Version:H04
Hardware Part Number:0CK927156AA
Serial Number:0000001795
System Description:0CK 20TDI RdW
System Abbreviation:J217
FAZIT Identification:TFK-06110.06.1600031795
hi everyone please help When trying to update the battery it dropped and the ecu died. It is not visible either on the car or with an external programmer. I read many forums and found out about some checksum on ST95640 that address 0x910 should be 2c 1c. I took out the chip and read it, but I don't know how to check this amount if it's ok. I am posting a dump if anyone can help or tell me how to check. I'm looking at it through a hex editor, but I don't understand what I should see. Please, I'm still a beginner, even though I'm an electronics geek, I haven't worked with software. It is an E60 with an M47 163 hp engine. The ECU code is 7799855, 0281012754. VIN: WBANC32050CP66054 .In the picture is that the 0x910 address I marked?
Hi guys UPA S corrupted the 9S12 2k78x DUMP , don"t use it to read this Dash .
Any one have full flash or can help fix it or give PIN
Thank"s in advance
I doing a project vw mk6 swap to simos 18.2
I can’t find ecu from a Scirocco
I have a Sharan ecu immo off butt this one is not working correctly
Can anyone help to covert to scirocco ecu the ecu is the same part number
Where can I find the immobiliser code for my 1996 MK1 Clio RT 1.4? Preferably for free or very cheap.
There is a button on the wiper stalk that I can use to somehow enter the code, but unfortunately, I do not have the owner's manual or any other documentation of the car, so no chance of getting it from there.
I have few questions for some of them, for my better understanding :
1. VP pump - as I read there is values in mVoltage, which controls solenoid actuator for the injected fuel quantity for delivery plunger? correct me if I'm wrong?
2. VP pump - how the values in mV are related to quantity of mg/cyc? Is there a formula if we want to reach more than 51mg/cyc?
3. SOI map - as I know this is CR before TDC, in this case positive number mean degrees before TDC, negative number mean after TDC, right?
4. DOI map - as I know this is duration in degrees for fuel injection. For positive number, this is degrees duration, but for negative number is not clear what mean for ECU? Probably ignore them or equl to 0?
I am needing some guidance on what to do.
I am needing to learn how to do the unlocks on GM T87a and T93 TCMs. I am able to get the EEprom and Internal flash files as a .bin file. I’m able to write as well. I’m just needing some guidance of what do I need to change in the files, or what do I need to patch in? I’m wanting to learn though, I don’t need a service, needing someone willing to teach an amateur.
Hello,
I have a problem with mileage correction of Vito W447 2019 year with Visteon instrument cluster. I changed mileage in eeprom 95640, put can filter set to 222 and after ignition on return original mileage, tried with another can filter set to w166, mileage dont change back, but all systems stops work and stores fault in CAN communication with instrument cluster.
I would be so grateful if anyone can help me to solve the problem !
I have a Continental V56.12 ECU from a Citroen C3, I want to read it with Multiprog Xhorse, it can only be read in boot mode but the program does not show me how to connect it to boot
[font="MHH Font", Calibri, sans-serif]Hello my good people. I have a big problem and I need your help. I have a Golf 7 2016 1.6TDI 81kw with DCM6.2V. The ECU is bricked, i just have the ori map from OBD VR, no eeprom. I got the same donor ECU from the scrapyard. The car does not crank or start, the fan starts at full speed on ignition. Could someone help out please, what can be done to get the donor ECU to work? [/font]
[font="MHH Font", Calibri, sans-serif]Thank you all, with respect[/font]
