Hi friends. Anyone have an specific Hyundai Genesis 2.0T BK2 2013-2014 260HP SIM2K-141.1 MPC563 Damos good definition??? XDF could be too. SIM2K-141 are different in several structure areas, like load, boost and torque management. Ori file is attached.
Hello
I need help, I have added the SA965 TAXI code to a 213, now I need to do the SCN, but I am not sure which modules need to be updated with the new SCN, I know the ABS module and the dashboard, can someone confirm which modules are involved in SA965 in a 213 from 2020?
New OLS826, OLS824, and OLS818 verification DLL files are required. Please don't tell me where to update, as I only need DLL files. Thank you very much for your help. I will thank the person who helped me.
So, I’m working on a car that wants the adaptive LED lights removed and xenon lights put in. The problem is that the headlines they have currently are from USA and the lights they want installed is from Kazakhstan (8 pin). What I am trying to figure out is what are the pinouts for the light in the picture? With the pinouts I’ll have to change the connector wiring location to make it work. I have researched and found some stuff but not related to this headlight.
I don’t know what vehicle it came out of so I’m stuck in limbo right now.
I have a problem with Adblue. I need to turn it off permanently. Transit 2019 sid212. The file comes from dcu17pc43. SCR has been started. A broken tube fell out of the SCR injector after washing the DPF. Can the DPF be removed in the future?
[font="mhh font", calibri, sans-serif]Hi, I would like help if someone can make Tune, egr and dpf off on the file for Mercedes sprinterEDC16cp31-6[/font] [font="mhh font", calibri, sans-serif]SW: 1037505836[/font] SW upg.: P40975T0 sprinter_6469025800_093800_1037505836_P40975T0 [font="mhh font", calibri, sans-serif]Thank you in advance[/font]
Hi
I need two file working for ezs w220 (215 545 06 08) two prosessore 1J35D. I read that these processors seem to have corrupted files.
I want of transport protection in file
Hi
anyone have good solution with Toyota hilux denso adblue off?, i have nuo volta, swiftec, ecu company i tried with all software and all of these solutions after some days/km there is a dasboard counter/message that display the remaining km to stop the car. Even with unplug injector and pump is the same. If unplug adblue ecu i get U010E communication error that appears not to be in the file as this soft already disable it. As far as i can understand maybe comming from body ecu.
Any help apriciated, maybe toylex can do the job?
I need to write eeprom to Front BCM of Jaguar XF.
Front BCM D-Flash & EEE Corrupted/Blank
P-Flash Seems ok. No Data in Eeprom of D-Flash. So can't repair it.
I have the Eeprom from Rear BCM can this be used or does it req converting suit Front BCM?
i have a Bmw F25 here and the old CIC have black screen very often.
I stored when screen ist active: sig, cert, fsc over esys. Maybe i can save the generalPersistencyData_DiagnosticSWTController over ftp?
After that:
Installed used CIC
updated over ista+ IStufe F25-2024 from last week
changed vin with esys
deleted over ftp generalPersistencyData_DiagnosticSWTController
or used virgin generalPersistencyData_DiagnosticSWTController
want to load fsc, cert etc with esys.
I have no clue what i done wrong. fsc are rejected and navigation is grayed.
I searched alot in forums. I have icom and bought enet cable for ftp.
Maybe someone can help me with this problem? The tutorials are not working.
Can someone please check if the files are ok?
I have worked on several FRM3 but this is the first time working on FRMFA, I have managed to read both flash and eeprom, but I have no clue of how to check if they are ok =/.
If they are indeed ok, in order to clone I just need to swap the EEPROM to the new unit right?
[font="Segoe UI", "Helvetica Neue", Helvetica, Roboto, Oxygen, Ubuntu, Cantarell, "Fira Sans", "Droid Sans", sans-serif]I run a parcel delivery service with a fleet of Sprinters. The vehicles are limited to a top speed of 125 km/h. Unfortunately, some drivers are not very gentle with the vans, causing them to wear out quickly. My idea is to limit the RPM to reduce wear and tear. Does anyone have an idea how this could be implemented?[/font]
