could someone verify if the Xentry crankshaft sensor adaptation routine is correct?
P031509 is shown and impossible to adapt. No other codes.
Xentry show to keep 3000-3500rpm for 2sec, the 1400-1800rpm for 2sec, at standstill handbrake engaged. Show adaptation unsuccessful.
Renault with same engine, procedure called flywheel target programming and is done while driving in 3rd gear from 4000rpm to ~1000rpm while coasting.
There must be something more to it. Maybe some other aspect of engine not okay. Runs okay. Maybe some slight hesitation during steady driving intermittently.
Hello, i have this Jumper and i want the schematic for this car because i have a permanent error after start and i suspect wi9ring!
Can someone help me with schematic from ecu to turbocharger?
Ecu is SID208 Car is from 2012 22 engine
VF7YBTMFC1233380
Thx!
Hello members, i have all smartkey lost Vw Sharan with instrument type vdo NEC24c64 2013-, make dealer success but when i push the start button it wont ignition ON,..i try to learning the keys on bench but error, it wont enter the learning mode..i have no clues which step that i mistaken.
Good day,
I have a problem with immo off in hyundai accent KEFIKO MG7.9.8 with automatic transmission. I read ECU with ktag boot mode and do immooff myself in the mpc file. Now the ecu does not see the engine revs.
Could someone confirm if the immooff file is done correctly?
Or correct or tell how?
Hey guys. Hope everyone is fine or at least doing things not to stay bored.
Today I have this Mercedes-Benz w190 in the workshop and the battery got discharged so it got locked.
Like any other LiFePo4 battery installed in the newer cars it has the same principle. Once it reaches the minimum allocated voltage, the flag will be written in the eeprom of the BMS. This time its the NXP Freescale MM9Z1J which has eeprom and pflash to read out.
I've reade out the eeprom and pflash, and tried to unlock it with the Tesla repair function as it has the same chip inside, it worked, but now there are lots of errors in the car, saying that the "message is missing", "no communication with lithium battery", even tho the voltage is there now and battery is unlocked. So I need to find that pesky code which is wrong for this chip. Or maybe someone got the solution for this battery already.
have troubles with mb gle w292 om 642
car got two fault codes about temp sensor for turbocharger. After short driving first show p2080fa , after one minute show second fault p24284b. First change temp sensor with OEM , then remove dpf and cat and fully service clean , then remove bad ecu tune - with new oem software from MB and fault still blinks after drive. car goes into limp mode. Installation looks fine. What ive do wrong? Thanks for reply
Hi
I have a problem with a Porsche Taycan where we can not get the ignition to turn on. I have done the following:
- Checked with scan tool. It can not see the drivers door and drivers side passenger door module. I have moved the drivers module to the passenger side and it works on the passenger side so module should be good.
- PCM protection message on the centre screen.
- Have checked grounding where possible.
- Tried with the key in the cupholder but still cant ignition on.
- All fuses and relays checked as well.
I have tried work with PIWIS 3 and our Lauch X431 and cant make progress. I am focused on the drivers door module not being seen by the scan tool - could this be linked with PCM protection?
Friends. I need an eep wirgin for the B&O Audi A5 amplifier 8T0035223 AK sw.0170 hw.H08.
possibly an eep file from the amplifer and gateway. VVdi will unlock my eep. In the original amplifier I have error 0003.
Hi all, need some help on a w177 steering angle sensor issue.....
Car is a 2020 A250e Auto
Basically the indicator stalk was faulty so ordered a complete unit with steering angle sensor didn't realise until i received that it was off a manual car, do just replaced the indicator stalk the angle sensor has to be removed to do this. When fitted back on the car the traction control light was on and the car was pulling to the left when taking off, messed about with the angle sensor and believe i damaged it.
So ordered a complete unit for the correct auto model fitted it and still same thing.
I have a Autel mk908 diagnostic machine, reseted the angle sensor the car doesn't pull now but tge traction control lights are on and comes up with "data received ftom traction system control module were implausible"
