Friends. I need an eep wirgin for the B&O Audi A5 amplifier 8T0035223 AK sw.0170 hw.H08.
possibly an eep file from the amplifer and gateway. VVdi will unlock my eep. In the original amplifier I have error 0003.
Hi all, need some help on a w177 steering angle sensor issue.....
Car is a 2020 A250e Auto
Basically the indicator stalk was faulty so ordered a complete unit with steering angle sensor didn't realise until i received that it was off a manual car, do just replaced the indicator stalk the angle sensor has to be removed to do this. When fitted back on the car the traction control light was on and the car was pulling to the left when taking off, messed about with the angle sensor and believe i damaged it.
So ordered a complete unit for the correct auto model fitted it and still same thing.
I have a Autel mk908 diagnostic machine, reseted the angle sensor the car doesn't pull now but tge traction control lights are on and comes up with "data received ftom traction system control module were implausible"
[font=Roboto, "Helvetica Neue", Arial, sans-serif]I will buy a used Poldiag MQB, [font=Roboto, "Helvetica Neue", Arial, sans-serif]If you have one for sale, send me a PM. Regards[/font][/font]
ECONIC RUBBISH TRUCK
This is because when you have to change the speed of a garbage truck, i.e. at the back to drive up and down with garbage cans, you need a file to code. I need someone to give it to me. Willing to pay
I have freelander 2, 2007 diesel engine
Sympthoms was that car started when it wants, but now it won't start
I have read the codes but nothing, after 7586576 tryes ECU gives me trouble code ( P1259-87 ) and BCM somethimes said following code (not always) DTC B108D-23 Start Button C ,
I have checked all the wires in front fuse box all the grounds , checked BCM and bcm wires too but still nothing
Somethimes car crank but not start the engine work
[font="mhh font", calibri, sans-serif]all key lost, after read fk72-19h440-af[/font] [font="mhh font", calibri, sans-serif]eeprom file was corrypted, solution repair file , or i have add key using BCM Dflash? [/font]
I’d like to extend a huge thank you to Fantomel for generating the KESS V2 Clone Rework guide. It has significantly improved the performance and reliability of clone boards. I followed the steps to replace components like transistors, diodes, and capacitors, and everything worked perfectly. I also applied my own soldering technique to further enhance stability.
Thanks again, Fantomel, for contributing to the community.
If this information helps you, don’t forget to Thank and give Reputation.
Hopefully someone can help me with this one, I have a 2016 toyota hiace that I need to correct odo on, toyota is outside my usual area and am unsure if my read is even good, did get 2 reads the same.
Chip is a c66 msop - I read as 93c66 amtel.
Attached is the read if someone can confirm it is a good read first of all, and then help with the algo to adjust from 317xxx ks to 271000 ks
i've been asked to help clear dtcs and try to force emissions readiness to complete. this dodge viper has been tuned with hp tuners for a custom supercharger.
ive loaded the file into my vcm editor and i can see the dtcs, my question is does anyone know which error class disables the dtcs and allows the readiness to complete. my understanding is if I disable all dtcs related to emissions, this should "force" the readiness monitors to complete. unfortunately, there are 1 - 15 options and disable and i am not sure which one to choose?
I’m currently looking for a reliable key tool that works with both FBS3 and FBS4 systems for Mercedes-Benz. I’m on a budget, so I’d appreciate any suggestions for tools that can handle these tasks effectively without breaking the bank. If anyone has experience with a tool that can manage both systems, please share your recommendations!
Hi, I have a JD 6190R tractor, I see uses the same parts in the engine that 6210R (next model), I have JD advisor cracked and I want upgrade with PLD file up to next model (6210R) is possible? Thanks
Hello Mhh
Can anyone please share engine cooling fan wiring diagram for maserati levante, ( vin :ZN661XUA8HX207370)
i have probleme communication for Fan
thankx in advance !
Hello,
I am new to this forum. I am wondering if anyone could help me find the parameter file for Audi A8 4H air suspension control module (SW#4G0907553G). Need dataset#4H0909553H 0038. I have ODIS engineering but don't have online access.
Thank you in advance
Hi, I have a Bosch ECU MED 9.1.2 that has the brake switch circuit malfunctioning. Which tool should I purchase to clone this ECU onto a good one or to backup the ECU in case a repair is failed. The ECU works just fine but the brake lights remain on due to the brake switch circuit malfunction.
When I swap the slave and master ECU the brake switch error is gone however the car will turn over for a few seconds but not start due to Security Issue displayed on the Dash. Any way someone could help? Could I swap the master and slave ECU and reprogram the slave to the master and the master to slave?
I have a VAS 5054A OKI full chip clone. Would this work and what software should I install?
![[Image: bH70uo7.png]](https://i.imgur.com/bH70uo7.png)
![[Image: Xr68DRe.png]](https://i.imgur.com/Xr68DRe.png)
