Please help to extract pin code from ecu 0281001966, 038906018FD eeprom dump.
Eeprom read as 24c02
.
The dashboard needs to be replaced, because there are problems with it. For the new(used) dashboard I have pin. Tried read Pin via obd with many tools - no way to read...can't.
Hi, I'm new to the forum, I don't know if I'm in the right group. I have a problem. Audi Q7 3.0TDi EDC16CP34 in the car, the ECU was drowned, I can't find the ECU that was in the car
Original ECU:
4L0 907 401 - 0090
0 281 012 772
1039S14596
I got the ECU
4L0 910 401M 0030
0 281 013 689
1039S18920
Is it possible to pair this ECU with my car? I tried IMMO OFF with the original SW which was in the ECU 4L0 910 401M but as soon as I turn the key to the first position it starts the fans. Any advice on how to run this ECU on my car?
hello my friend please i need to make mileage correction for mercedes w203 instrument cluster
eeprom 24c16
old mealige 301450 km
need to make it 234000 km
thanks alot
Citroen c4 2011, 90hp, EDC17C10, file should be stage 1 with egr and dpf off, tuning service wont check it for me because 28 day guaranty is over...
Hi, i bought this file 2 months ago and everything was fine until yesterday. Big amount of White/grey smoke from exhaust while driving like it was doing dpf regeneration and then stoped after some time.
Today I checked with delphi tester and partice filter particles were rising but it should show 0 right?
File should be stage 1 with egr and dpf off.
Can anyone please check this file or give me tested one ?
Ive registered for Servicebox
Ive purchased tokens for peugeot
Ive downloaded Diagbox and updated to latest .200 and activated ok
My passthru Vci is connecting to the vehicle and reading control units
but then it comes up with authentication box to enter id and password
i enter the service box id and password but says identifier incorrect so i cannot proceed with diagnostics and doesn't use the token.
Im not sure what I'm missing or if there is a different code i should be using?
hello,
please i am looking for UDS library for arduino or esp32 to send one frame and multiple frames with UDS ptotocol using arduino or esp32
is there someone do it before ?
Thanks in advance
hello help
BMW e39 530d 351761
Client want hardcut flames 4500 rpm and Launch control at 3500 rpm . I tried make but .... sound wasnt as good as client want.
owner make me crazy, call me every day . could someone make it ?
I went though a little arduous process of reading with ktag clone (with adapter, positioning frame and solder 1 wire)
but discovered that my ktag is not supplying voltage to the red and black wire that should go to the top right pin of the ecu and bottom left.
And so I got error message "cannot communicate with ecu".
So I ditched the effort.
hi can somone help remove adblue for astra k 1.6 cdti ecu acdelco e98 try all ready couple solutions swiftec ols etc without success always scr count on dash
i have obd read autotuner
i can pay for good working solution
good evening colleagues, I am the owner of an opel meriva A, I am here to ask for help to encode a used radio on my car.
I read the eeprom of the old radio and also of the one recovered from the car wrecker, I also performed the CID reading (delphi gruding) with 25080 atmel memory.
can anyone match the new radio to the CID?
I have foult code in the KAFAS on BMW G12 2016 so I received repair kit for it .
I have repair kit FSC but I don't know how can I use repair kit with ESYS .
Hello guys, I have a problem with Sebring 2007 2.0crd ( vw engine) after pcm eplacement
it wont crank or start. Ecu was replaced due to p0605 internal eeprom error with ebay one (same p/n).
I entered vin and did replace pcm function in wcm module with autel im508.
I tried old pcm and the same thing happens no crank no start ( tried to write vin to old pcm and sync it with wcm )
I tried to ignition on and power starter with power probe it cranks but wont start.
All fuses are good , tried to unhook battery cables and short them for TIPM reset , same thing
Used alldata diagrams and measured from pcm to TIPM continuity is good, and from TIPM to starter continuity also good.
I am thinking of bad TIPM ?? , there are no dtcs, and red immo light turns off , car detects all keys and in live data section
there is start / run condition commanded when I turn key to start position ,
but the starter relay pid says off ?
