I'd need original and tuning file(DPF off, stage 1) for Opel Astra J A17DTR Denso.
I'm using MPPS v18 for read/write, but still hadn't tried it yet(read) because of risks associated with not possessing original file at first place.
Glad if someone can provide tested solution.
Hi, I bought Citroen Berlingo Multispace 1,6 HDi 2017.
Problem is that in car is only dash + key, there is no ECU and BSI. I checked parts catalogue and I have parts numbers of ECU (there are two numbers 1613645480, and 1677612380) i googled those numbers and I found two BOSCH numbers 0281034189 and 0281032456, but which one is correct?
The same thing with BSI - catalogue says 1613583780 and 1663366980 (second one has indication "ESD" whatever it is), after googleing i found 3 numbers: 981218948000, 981218948001 and 981218948002 (but which one exactly)
First question is - can anyone tell me what exact numbers of ECU and BSI are correct?
Secondary: I have tool to read and write BSI eeprom - to make it virgin and code it with Diagbox is it enough to make all bytes "FF" ?
Third: I plan to buy used ECU and pay someone to make it virgin and code it with Diagbox, is it possible?
Good evening has all I am struggling to unlock this electric 500, they put the booster on battery 12, and the car does not start anymore errors in diagnosis P0AA1 "Battery Pack Positive Contactor Circuit " P0AA4 "Battery Pack Nrgative Contactor Circuit" you have solutions
Hello , i have an ECU md1cs006 from Mercedes w177 , and i have Scanmatik 2 pro with Pcmflash software .
I have seen that Pcmflash to work with md1 ECUs ,has to be activated module 92 , someone has this module or can sell it to me ?
Please can some1 share good forscan version to do a ford ranger 2017 sid209 replacement ecu programming
I have normal forscan with extended license but when I try it says I need paid license so I'm confused because isn't a extended license same as paid license?
Replaced engine. Now I have p2138 Pedal position sensor correlation a/b. Replaced pedal. Same thing. 1 sensor reads 0% the other reads 6% cant find anyway to relearn the fully released and fully depressed learned positions. Removed battery cable for hours. Tried to reset every parameter I could.
Hello, I have Mondeo diesel 2002, fuel pump is bad, now is fitted used one but Pats wont allow start, error B2139 The PCMPowertrain Control Module) identification was not recognized by the PATS(Passive Anti Theft System) module.
Problem is owner have just one key, I know you can erase keys and then program but minimum 2 keys.
I have Autel MaxiSys MS908 Pro with J2534 and Forscan, unfortunately dont have VCM for IDS
Maybe to try with one key and coded access, If anyone have incode for this outcode
Hello All
Need to disable limp mode strategy on a 2007 Jeep Grand Cherokee WK 3.0 CRD with EDC16CP31 ecu.
Currently it is limiting power with red engine light and there are no dtc stored. Can someone help with this?
hello.please friend need help for scenic 2 2005 1.5dci.i need wiring connector under driver seat water damage.please have somebody wiring for that connector.thank you
I'm trying to read the codes from ABS/ESP on this car with a lit VSA lamp but I cannot access ABS with my Autocom 2020. Can anyone confirm if the new 2021.11 version can do it?
hello boys
i have an nissan pixo with bosch me 17.9.5 , nr. 0261s04260 (same ecu suzuki alto )
i'm trying to do immo off , but eeprom solution not work.
do you have a solution for this ecu??
thanks boys
solution.
![[Image: f5f709f1677b324c916e7a8a7070e3a8.jpg]](https://uploads.tapatalk-cdn.com/20240926/f5f709f1677b324c916e7a8a7070e3a8.jpg)
