hello need full bdm for ecu altea toledo ecu n bosch 0281012291 ref 03G906016HE sw1037372726 please, thanks

Hello all can someone help me on this ecu? I need immo off .thanks
iveco daily 2008
EDC16c39-5.A3
0 281 012 193
2008

Hi all,
Anyone know the injector data address on ford delphi tdci ecu?
File attached
MJP

Attached Files

my TDCIorigial.zip

82

164.39 KB

Download

Hello dear friends.

Can you clear or do you have software this crashdata?

It is a Fiat 500 with 25320 eeprom
Airbagmodule 51870005

Is there a program like AllData and Mitchells OnDemand that is in French?
These programs are useful but only in English.

HELLO, I HAVE THE KTS 200 AND NEED THE INITIAL INSTALLATION CD AND IF THERE CAN HELP ME AND IF THERE WAY to unlock it.
THANKS

hello, I'm a little time with AUTOCOM, and installed as the tutorials, most every time I make a diagnosis is giving error "VCI not found", already reinstalled, use 2011.3. tó pensdando in exchange for Delphi 2012.3. what do you segere the MHHauto me to do?
I will attach some pictures ..... funny that it stays on the screen and unlimited lincença tbm says has 5 restrictions do not know what that means. tanks

Attached Files

Thumbnail(s)
           

Can anyone sell me this:- Volvo Prosis 02.2012

Thanks!

Hi M8 Members,

ICOM-Application İmage-01-20-01
ICOM-Boot Image-01-14-00
works in all versions,

Good Luck...

Rar Pass : By ircpoLice

Attached Files

icom firmware.txt

314

66 bytes

Download

I am Looking for a keygen for the Mitchell manager V5.9.5.10 can anyone lead me the right way

Thanks

Hi!I have problem with one Renault clip, when connect to car, softer see sonde and see car but when start diagnostic then got messages BATERY VOLTAGE LOW: RECHARGE THE VEHICLE BATTERY BEFORE RESTARTING THE MULTIPLEXED NETWORK TEST!I am test to more car but valtage is good!Some Renault car work but more car not and write this messages!

hi all member please you help me for service manual nissan mach 2004 .i need wiring diagram.please you help me

hi

got a little problem megane 3 1.5dci wont start it cranks over but will not fire

story is:

car came to garage with leaking coolant pipe, while mechanic was changing it he accidently shorted +12V from alternator to engine with spanner. engine was off but he cant remember if ignition was on or off.

there are no faultcodes stored in ecu, fuel is getting to injectors, crank + cam sensor working ok, there is no pulse going to any injector check with a bulb and nothing.

normally if there is a pulse bulb flashes

immo light goes off and no faults

does any1 know whats modules are coded and what could be problem?
do these have a seperate edu module??

any help would be appreciated

cheers

Hi there to you all, can you please clean my airbag dump:

Renault Clio III
8200 645 161/---
Bosch
0 285 001 959

Thanks

Renault Clio III Bosch 0285001959 8200645161.rar

66

1.31 KB

Download

Hi Peoples,

does anybody know which prog replaced BMW TIS for car newer then 2008my

thanks in front
Bee

hi,
looking for help with 12 digit login pin please from VIN

VF1BR120H39873041

2008 renault clio III

THANKX

Hello,

we can i add icons on the new desktop?
Will das add.

Sorry for my bad english!

can someone send me a torrent link or the actual file to a non-russian gen for on demand 12?

Please help immo off from Audi ME7.5 (1.8t 2003y)
95040 chip

Attached Files

a4 immo.rar

43

368 bytes

Download

Hi I have a peugeot 307 hdi year 2003

and I have to adapt kilometers.

has a dashboard with micro nec sagem
I want to know that memory should be acting in the bsi to km

thank you

Hello that such friends need help with a forum nissan sentra 2008 vin 3N1AB61DX8L721317, csv files need to J2534, I need to reprogram the transmission, I hope I can help peers.

Attached Files

Thumbnail(s)
   

B8257, i have got this new bcm and will need the NEW BCM PIN CODE, please not the old code for super code but the new bcm code, please so,someone help. thank

Hi
Need help on durango, i have on dash no bus. Need flash to ecu or any info about this fault. Maybe checksum correct need.
2002y engine 4.7 v8 pcm Motorola.

Thanks.

Attached Files

Thumbnail(s)
   

flash.durango.m28f220.rar

42

102.36 KB

Download

hallo friends
in my store i have a m/s clk200 kompressor 2003 model engine number 271940 i have a noise from the kompressor probably the bearings but i dont know how to remove it is my first time with this car. i am not familiar with the mercedes
is there any diagram shows how to take it out of the car or any video i search at youtube and found nothing
regards

Hello and please help me.
After reading soft from ECU 2,2CDi sprinter coming fault in dash "Start error". Memory 5P08C3
I use to reading MPPS 13.0.
Any solution.
Kind Regards

1037351493.Bin1037351493.rar

92

164.07 KB

Download

Recovery DVD's Multilanguage
DVD contents:
Windows Xp SP2
Etis pre-installation
ETIS IDS version and does not include all of the installation of


Rar Pass : By ircpoLice

Attached Files

Panasonic Recovery.txt

262

1.05 KB

Download

carprog clone CAN BUS repair solution!

Tested all version! Clone carprog Can-bus Communicate OK!

Price, and solution:
[email protected]

Edit By ToMiBoY
Please Read and Follow Forum Rules Here!
Rule #10
Thanks

Hello

Does someone know is it possible to put speedlimit on trucks with autocom?

Thank you.

NEW VividWorkshop Data 12.1 but there is no crack,
perhaps someone help

Click to thank password on pm

best regards

Attached Files

Thumbnail(s)
   

Vivid WorkshopData ATI 12.1.rar

1565

16.53 KB

Download

Good day. I am new on this forum so please help me if I make any mistakes. I do electronic repairs on BMW's. After I fixed can problem on E46 318i auto facelift. The transmode light on the cluster comes up after driving car for a few meters. GT1 fault code says Airflow mass meter. I have replaced airflow and checked all wireing. Please can anyone help me