hello,I have bmw e83 X3 3.0SD m57 engine in my garrage ,so car is start and drive but no power,When i connect ISTA or IMPA software can't see EGS,DDE,CIC and DSG,all another modules is connect. if connect with Autocom and thinkdiag i can see it but not get all live data and get just AirFlow sensor.If i change it with new i get same error.
Someone can help me to connect it with ISTA? If problem is in FlexRay someone help me how to fing it?
All fuses and plugs are inspected,all plugs looks good,and fuses.
I have problem with Audi A6 C7 BCM2. Have active 02768 fault and warning on dashboard with steering lock. I think BCM2 files are corrupted. Could somebody check them???
[font="MHH Font", Calibri, sans-serif]Hello[/font] [font="MHH Font", Calibri, sans-serif]Can someone get me the original file and the file with egr and dpf off?[/font] [font="MHH Font", Calibri, sans-serif]Mercedes sprinter 315 cdi 2008[/font] [font="MHH Font", Calibri, sans-serif]EDC16C31 0281014344 A6461501677 1037505811[/font]
Hello,
I'm looking for any DAMOS/A2L/OLS for SID321.
Attached is the binary of the .ols I already have.
If you have any other than this please send me an offer.
Hello
Anyone have fullbackup from bkd with edc16u34?
Its from swap auto to manual org ecu are 03G906021LP 0281013283.
Any fullbackup from bkd compatiblity
Thanks
Hello, Can anyone help me clone the BCM2 for ORI file to donor file? Since it is a older version will it be okay if I transfer DFLASH data directly from Original to donor or do I have to clone the immo data from old to donor? Thank you
Is it possible to transfer DME ISN from donor CAS3 to original CAS3 . I got a donor lockset from and auto BMW 325i E90 for use on a manual 325i. So i want to use original CAS with donor DME
Hi guys,
Ive made the mistake of flashing with ktag Me7.1.1 and now Im pretty sure my EEPROM is corrupted.
Can someone please check it and PLEASE fix it PLEASE
l Will post The EEPROM READ and THE KTAG BACKUP read
Thanks GUYS
Hi, i have a huracan with rear steering actuators, that do not accept the basic settings.
this are the errors:
Post-scan DTC 01 - Engine Control Module 1 ( 1 DTC ) DTC Description Status
U041600 Invalid data received from vehicle dynamics control module Active/static
03 - Brakes 1 ( 1 DTCs ) DTC Description Status
C200700 Rear axle steering control unit No function Active/static
0C - Rear axle steering 2 ( 4 DTCs ) DTC Description Status
C11D254 Power steering control unit - missing calibration at rear Active/static
U041600 Invalid data received from vehicle dynamics control module Active/static
U116900 Local data bus Message missing Active/static
B200FFF Internal malfunction Passive/Sporadic
5F - Information electronics 1 ( 2 DTCs ) DTC Description Status
B105401 GPS antenna Electrical error Active/static
1795 Please refer to vehicle service manual. Active/static
CB - Rear axle steering ( 5 DTCs ) DTC Description Status
U041600 Invalid data received from vehicle dynamics control module Active/static
U116900 Local data bus Message missing Active/static
C11D254 Power steering control unit - missing calibration at rear Active/static
B202900 Adaptation not performed Active/static
B200FFF Internal malfunction Passive/Sporadic
Anyone has the idea what is missing? that do not allow to be coded. One of the actuator i have changed for test it, if it's damaged, same error with 2 actuator.
Anyone on here have access to Damos/A2L or super map pack for - SDI21.2 W2200H2000000 9P1906023CJ (991.2 carrera 3.0L and 991.2 carrera S 3.0L) ? Please let me know how much.
Hello, i have a damage 0281001322 MS5 and a used one to transfer the immo code,
there are 2 UV erasable eeproms on socket, but i don´t know were the immo is located.
Please someone inform how to clone this unit, eprom,, mcu ?
Hello. I have a w212 with a camera in the window - ILS. Is it possible to code reading road signs? I heard that it is possible, maybe someone knows more about it?
I have a 2015 Mazda 3 I recently replaced the PCM and programmed it to the vehicle's VIN but now I need to get into pats and sync it along with relearning the keys I believe, but my issue is that I can't for the life of me figure out how I can get an incode. I desperately need help!!
Here I have a BMW E36 320i with Bosch M3.1 ECU 0261200402 and chip 27C256. I did pops and bangs, and rev limiter.
The problem is, the car between 1500-2000rpm fails a little bit and jerks, like if some coil is failing, but only when throttle is soft pressed, at full throttle the car runs perfectly.
The problem is I didnt touch anything between that revs. I am broking my mind with this. With the original chip the car runs perfect.
