HELLO TO ALL THE COLLEAGUES IN THE FORUM IS THERE ANY SPECIALIST IN THE GROUP WHO CAN HELP ME WITH A FORD F250 2024 USA MARKET , TRUCK I HAVE THIS DTC P20E800 REDUCTANTE PRESSURE TOO LOW AND I DON'T KNOW WHAT IT MEANS. I CAN PAY FOR THE HELP
I think the PIN code is 8932 from the donor ecu, but I can't reset with carprog and with opcom, I tried to reset the ecu with OPCOM but I put in the code and OPCOM tells me CHECKING THE CAR'S PASSAGE... And I can't reset... it doesn't deny the code but it doesn't accept it either, I don't know why. Can someone get me the code for this eeprom+flash read with kess v3 on bench? or can someone reset from the eeprom? thank you so much.
Hi mates!
I would like your help to erase a code p0420 on ECU.
It was reading with Tactrick and ecuflash software
If some could help me, I would appreciate your help.
thank you!
"Hello guys, I have a BMW E46 320d 2002. I have the stock file and the map, but somehow, I feel like the file is not that good. The boost comes in a bit late, and there is no significant performance gain from the stock file. I would like to have a damos file for WinOLS to analyze and learn more. If possible, I would also appreciate it if someone could optimize the file for me. Here are the car's details:
Bmw Ecu Type BOSCH EDC16C/C
Bmw Hardware ID 07789572
Bmw Software ID 07788337
Hardware Number: 0281010565
Bosch Software Number: 1037351788
i have a 2016 sprinter, om651. i added the oem cruise assembly. i have a c4 with offline xentry sept 2023.. vediamo 4.2.2 activated and the seedkey calculator 3.0. is there a step by step guide?
Opel Insignia 2014
2.0 CDTI 130HP Automatic 6 speed transmission
EDC17C59
0281019867
1037543026
I started my own stage1 but I'm not able to Log the I.Q. and Torque with AUTEL MK808.
So I'm not sure about the miss some Single Value Torque limit and my Torque monitoring off solution that's why stage 1 need.
Also I'm not sure about the Aisin 6 speed gearbox has limitation to the ECU regarding torque.
If somebody can give me a hint that is also good.
Hi everyone, need help I lost all keys from my Seat Ibiza andmy locksmith have made for me new keys but he is not able to adapt them because he can't read the immo data over obd. I have read ECU 93C86 and Dash 24C32 module maybe someone is able to give me the immo data and pin code.
I'm new here and i have a question. I have an issue with a Mercedes s550 2008 , the electronics of the left driver side is not working and some times the car won't start right a way. My MB star c5 is telling me that the front SAM is not the right one and is not receiving CAN message from central gateway. And sometimes i get engine fault code P0018 and P0016 and the trunk does not open. When i checked the CAN I did not find any fault codes. Do you guys think it's a CAN problem or a SAM Problem?
Hi, I have a problem. I did dpf off egr off using davinci. After removing the controller, disassembling and downloading the FLS. I uploaded a new file, put everything together and since then after starting the car in the cold the revs jump for about 4s. I tried uploading the old FLS. and nothing helped. Could it be the fault of a poorly disassembled controller?
Please I need immo off for a Peugeot 206 2.0 GTI with IAW 48P.10 ecu. I already tried to put all FF on 25080 without success.
I included the eeprom reading
BCM is fried on this 2017 Jeep Renegade. Can I buy USED BCM and Program VIN# or do I have to buy a NEW BCM and program VIN#? Current BCM is physically damaged and not readable so cannot clone. Please someone point me in right direction, also I will need programming service for whatever BCM i get (new or Used).
