My friend brought me Audi A4 B9 Edc17c74 Ecu. Car is 2019 or 2020 2.0TDI as far as I know, not sure thoug.
This is what I know about situation: They tried to update ecu using Launch and it stopped in midlle of flashing. After that other units can not communicate with ecu. They brought ecu to me. I managed to read it with AMT BST after ktag failed to do so. After that we sent files to 3rd party, who sent us file to flash. Unfortunatelly it didnt work either. As far I know only option in launch currently is flashing. No way to do any tests, live data etc. Or so they told me. Cant confirm because I havent seen what is actually doable in their end. So I think it is still corrupted, ecu in bootloader mode, or something like that. I will attach full read if someone could take a look, and tell me what could be done to save this ecu, if there is any way to do so. Original sw should be 04L906027BC 7154
I have a little problem with some IC213's. After changing from analog to full LCD, I noticed that the Assistance option does not work, it does not display the scale and the icon of the car in front of the car.
I also checked it on other IC213s - I have a dozen or so of them and on some it works without a problem, on a few it doesn't. This is not a coding problem, because I checked - I coded the IC 1 to 1.
I wanted to flash the non-working IC with the SW number of the working IC, unfortunately Monaco does not allow flashing with this SW.
Have you encountered such a problem?
Hi! Does anyone have a solution for Pops&Bangs ( And Idle REV limit rpm OFF) on A/C button or Cruise Control switch for Vw Golf 5 1.4TSI MED17.5.1 // ECU: 03C 906 032 N ?
Thanks!
hiu, it all . i got airbag a4 8k, 8k0959655L with internal error, no way to solve by clear dump ecc
anyway i have bought a same airbag ecu number, connected with odis online and did component protection as well ,but still have some airbag errors that are not installed on car.
tried svm , but not allow to recode.
tried also copy coding from old and write to donor with vcds and vcp, but not allow .have you any solution?
Is it possible to recover the BCM from a 2019 RRS on the bench? I messed up trying to program an edited CCF with Topix and bricked the GWM. I can't get any ignition now and no diag comms to anything. Enet cable doesn't connect either.
Hi, I have some questions about IMMO OFF, I hope someone will help me!
I used IMMO DOCTOR to do IMMO off for the Kia Forte ECU, and then I used KTAG to write into the ECU. But I've noticed that the engine won't start when the smart key is not in the car. "KEY NOT DETECTED" was found in the instrument. Does this mean that IMMO OFF is not working? Thx!
hi need ori flash
SW Version: AV41-14C204-DE
Serial number: 8468LA01350187
Part Number: AV41-12A650-DE
Hardware: AG91-12B684-DA
Calibration file: AV41-14C625-BE
Hi to all,
I received PD60 and want to test Fiat EDC15C7 with immo off on bench, does any know corect procedure, I have signal generator for engine speeed, simulate crankshaft signal.
Best regards
I have a Q5 and replaced the BCM2 and need to clone it. I used VVDI Prog Multi-Prog to copy the D-FLASH and P-FLASH, but the replaced BCM2 cannot be used. Can anyone help?
Attached is the original FLASH.
Thank you in advance.
Hi. Need to clone 04l907309Q edc17c74 ecu from tiguan 2.0d. can i use 04l907309P as donor (same engine, another ecology class)? who can help to clone? i will read flash and eep from both.
Hello everyone. Maybe someone has an original file with a number
8200498188
8200626676
The ideal option is a full flash + eeprom read in bootmod. But calibrations are also suitable.
Thank advance.
