Hi, i have here a Delphi DCM 3.5 from a Citroen Jumpy 2.0 i have write to 5 "Tuning Companys" all have the same Problem with egr off and after that the DTC "P14A3" and blinking Engine lamp.
What is the Problem with this ecu ?
All guys said "its testet solution" not our fail must a other Problem with the car ...
But i have read that few tuners can`t do this ecu.
I search a working solution not a "test this or this or this or this" i will not pay for test options and after few "test files" no respond, no money back.
The Last guy write send me the dtc inside EOBD.
In EOBD i can`t see a dtc
but i can seen inside citroen soft the P14A3
Good evening. I really need some help. Please help me turn off the particulate filter. It's going to be a long trip, I physically removed the particulate filter, it was very dirty. Now the error P1457 is constantly present and the car is losing power. Thanks
I have had success using the CGDI 2010+ keyless go keys in the past. Now I have a customer with a 2010 W221 who mailed me his EIS along with one original working key. He wants to add two more keyless go keys. I assumed this would be an easy job using the same keys I usually use. However, when I read his original key it's a V08. Uhoh...so is keyless go not possible for him? I am a bit confused as I thought facelifted W221 works with aftermarket keyless go. EIS part # is A 216 545 05 08. Please advise...
Hello ,
I have a caddy with an EDC16U34 Ctrl. An AXR engine was installed. Can someone create a Stage 2 for me with DPF OFF, EGR OFF? I think the turbocharger is a bit bigger and so are the injectors. The Caddy originally had 105hp and the AXR had the original 131hp. Thank you very much in advance.
hi guys, i've a Subaru forester 2010 2.0 petrol non turbo, after any dtc delete the car goes fine, after 2/3 day of use return sluggish and stuttering at cold and little bit better on hot.
spark plugs new, rear oxygen sensor new, no dtc. oil new, oil filter new. Advice to start any solution??
Hi!!! few days ago, we replace cluch and relearning and ok, because previously we have a lot off problem with 3 bars, after replacement car will be fine for 5 days. Today before start engine,we can see in dash 3 bar and odb scanner show p1800 c1323 error codes.
The problem will be solved only push for 10secons brake pedal, and relearing funcion was done.
Hello, We’re doing a CC( Cruise Control) retrofit on a 05 BMW (e90) 325i 2005 ,only thing left to do is installing the ldm module, so the question is does the serial number on those matter?
we coding with launch like $544
now show DTC 9520 and D35B at ABS
VIN : WBAVB11000PS54***
Hello!
I have problems withy 2016 B9. Car have 360 camera module factory installed, no retrofitting. Al was working, still all is working but camera module in trunk on left side is giving me headache. I had problems with car cranking so i changed battery wich was from factory. After 3 days with new varta silver also car didnt start, so i started to investigate and detected that camera module is drawing about 900mA of current regardles if car is locked, working, or ignition, and when i disconnect each camera module, draw is smaller by 150mA. Even with only module connected without camera or video out to multimedia, so just 4 wires - power and CAN line, module is drawing about 500mA. There is no errors in diagnostics, all is working, cameras, sensors, park pilot, everything great but battery draw is problem. Module disconnected and car start after 2 weeks without problem. I also tried other module wich is 100% ok and same problem. My module is working on that car without problem, that means module is no problem. Something is telling that module to stay awake and power cameras.
Did anyone had similar problems? Is there anyway to test can bus line, maybe this is making problems?
Thanks!
Hi,
Could someone check and synchronize the eeprom files of the Ford C Max 1.6TDCI EDC16C3 ecu and dash
REF BOSCH 0281011263
Visteon 3M5T 10849 GJ
I attach the original readings
Thanks
