Hello

I am having issues with doing immo off on this edc15 ECU with 35P08 eeprom.

Desoldered and read a few times with Carprog clone as 95P08 (only possible way for me), every time verify is ok and compared dumps are the same.

Is writing mod file as 95P08, safe?

Attaching Ori dump...

Attached Files

35P08_Ori_eeprom.rar

3

293 bytes

Download

Hello
As in thread subject, i´m looking for immo off in Valeo V34P  ecu from Peugeot Bipper, ecu Nr. 966454780, engine KFV
This ecu algo is different than standart PSA immo of solution.
WBR Rob

Attached Files

9665454780_org.rar

3

736 bytes

Download

Hello!

I need your help guys. So basically I got this Golf 6R MY2013 with coloured dash and Keyless system.

I tried to add a key with official AVDI by OBD, so I touched the key on the steering column to go to service mode and added the key on the 4th slot.

But now on the cluster, instead of mileage it shows 4-5 as if it was still in programming mode ?? 
Now I can't go back into Service mode even if I stick the key on the steering column, it fails to load the boot mode... So lets say if my Keyless system dies I wont even be able to start the car by sticking the key...

I have attached the configdata and immo data of my Dash that I managed to read my going into service mode on the table with pogo pin.. Anyone can help me ?

Dash Reference : 5K6920 8883B

Attached Files

VW Dash.rar

1

2.21 KB

Download

Hello, i have a problem with w213 both blind spot assistant modules. I have a fault B220600 (The current vehicle identification number is incorrect or not present), bur when i check actual values in xentry the Vin is correct. I tried adaptation in xentry,  hard reset in Dts monaco, but no changes. Please see the screenshots attached

Attached Files

Thumbnail(s)
   

Please code for audi concert serial is AUZ2Z3D2064712
Thanks in advance !

Hello, 
I have a problem with a VW EOS.
VW was replace a used instrument cluster. Now they have done something wrong, so that the VIN of the used clusters is now in the vehicle.
Is there a way to adapt everything to the correct vin? (the old and new dashboard have the wrong VIN) without having to buy everything new.
The car is driving with immo off.

Hi, I have a Fiat Doblo 1.6 16V Multijet. no engine fault, all cables and sensors checked and the car won't start. any advice?

Hello,

I need a security code for an Opel Vectra C CIM. 
Got this one from a car scrapyard.

Can someone help me please?

Regards,

Mrgalaxy1

Attached Files

ori eeprom vectra c cim 93lc76 04536626.zip

2

836 bytes

Download

hello,

i have installed xentry passthru 04.03.24 but i cant get it registered. all of the files i get are infected with virusses says defender.
does someone have the fullfix available or can help me with this? im new to xentry.

thanks in advance

Hi.

I need some new tools, currently i have a New Genius which i use for OBD tuning, but this tool does not support some Mercedes like CP10, 01 and W211 220 cdi facelift. Autotuner supports these over OBD.

I am not sure what i should buy, i mostly do tuning with deletes etc.

I also have a kess and ktag clone and a Foxflash unit, which i dont find stable and this reason i need to find some better.


Advises?

Thanks

Hello.


I m looking for a mappack/Damos for a Skoda Scout 1.8 TSI CDAA engine. ECU 1Z0907115F  /  0261S04090  /  399516

HELLO,
DUE BSI CHANGE, NEED CHANGE ODOMETER VALUE ON BSI, 
ACTUAL VALUE IS 890000 KM, NEED 94000,
THANKS

Attached Files

ST95160_EEPROM.rar

6

607 bytes

Download

Renault Fluence ZE manual needed, any help please? Primary MY 2012 and 
Wiring too would really help.

Hi, I have W176 , this car has been moved from one shop to another, the last shop told me that engine ECU was replaced with a donor, but when trying to personalize , instructions to crank when given , the starter will not engage, cranking motor is ok, there is a code in transmission 061000  No valid transmission variant detected, but nothing was done to the TCU , has  anyone experienced similar issue, please advice. 
Thanks

Hello friends,

i have one BMW E39 problem is car not starts, ews was damaged so i bought one and programmed key.
Problem is, that ECU and EWS data not compatible.
Is there some guy can sync ecu and ews togehter ?

by worked file, i pay 50€

Thanks in advance

Attached Files

FLASH BMW ECU 0261204467.rar

6

77.45 KB

Download

EWS 3(2)2D47J 1998.rar

3

440 bytes

Download

hello i need flashing pinout for my mucar 
please help

Attached Files

Thumbnail(s)
       

Hello
Has anyone read Iveco MD1CS069 with PCMFLASH module 92?
Thank you!




post pics

Hello, could I ask for verification if I did everything as it should be? I turned off the EGR
10139656aa_6g91-12b684-da

Attached Files

FORD_MONDEO_MK4.RAR

1

89.89 KB

Download

I recently bought an Bmw from a private bmw dealership. the car was tuned stage 1 before but now is completely stock. After I go to BMW for a diagnose got the "S 0777 tuning detected" . The car was with completely stock file, no tunning. Only with This error! After i went to a chiptuner to remove this S 0777 and everything ok.

Now i went again to  Bmw for a check and they said the car still tuned and i need to change the DME.  The car is running perfect i dont have problems.
I just need a certificate from BMW that the car is not tuned.

So my question is that... is possible the car get flagged in VIN with chiptuning? 

Thanks in advanced.

I need wiring diagram ICMQL modul...i have problems with front radar.....the vin is WBA8T510X0B456708

Hello, there was a bad airbag unit in the car, the crash data was stored there, a new one was made, but the unit still has errors and no communication (probably someone has already climbed into it before), I want to put a new one, but what I looked for, only the top number fit, with all 3 numbers I couldn't find any? what all has to be upgraded to the new one? what is the procedure for exchanging it for another one? Thank you.

Attached Files

Thumbnail(s)
   

Hello, 
I need 2 dtcs off for vw fox 1.2 simos 3pg7000 03D906033H 
the dtcs is 00301,01021

when anyone can make is thanks

Attached Files

vw_fox_1_2BENZ_ECU_Simos_3PG_7000_03D906033H_5WP44238_02_Flash_29f400BB.rar

2

164.2 KB

Download

Hi guys I replaced the instrument cluster in my 2015 VW Polo R Line 1.4 tdi FWD, doing this wiped the long code for my ABS module and I have no history of previous code to revert back to. 
Please could someone generate me the long code I would need, the details are

ABS Module - 6C0 907 379 K
VIN - WVWZZZ6RZGY106799
TPMS - Yes
ESP - Yes
Hill Hold Assist - Yes

Im a DIY enthusiast so im not sure if anymore information is required.

Thanks,
Manny

Hello, i have a 2016 GLE 4matic AMG all keys lost and it's FBS4, i have ordered ignition switch and key, i have xentry and C6. I want to know if i can adapt the igniton switch to the car if i have online access with xentry

Hi, i have here a Delphi DCM 3.5 from a Citroen Jumpy 2.0 i have write to 5 "Tuning Companys" all have the same Problem with egr off and after that the DTC "P14A3" and blinking Engine lamp.

What is the Problem with this ecu ?
All guys said "its testet solution" not our fail must a other Problem with the car ...

But i have read that few tuners can`t do this ecu.

I search a working solution not a "test this or this or this or this" i will not pay for test options and after few "test files" no respond, no money back.

The Last guy write send me the dtc inside EOBD.
In EOBD i can`t see a dtc
but i can seen inside citroen soft the P14A3

Attached Files

Citrön Jumpy.rar

3

406.46 KB

Download

Hey guys,

can someone please help me to do immo off without emulator.
Its SID803A from Ctiroen

Thank you

Attached Files

citroen_9666095880.rar

1

1.29 KB

Download

Please Need Full bakup mjd602

d

Attached Files

Thumbnail(s)
   

need tested solution pls
egr off sid202

thks

Attached Files

Ford_C-Max_2005_1.8_TDCI_115_hp_Siemens_SID202_OBD_NR.rar

3

30.17 KB

Download

hello,

does anyone know how I can permanently change the settings?

Attached Files

Thumbnail(s)