hello, I tried with davinci delux, not with swiftec, is there anyone who can make egr dpf? thanks in advance
ford kuga 2014 dcm3.5
dv41-14c204-al
spare: dv41-12a650-al
Hello guys I have Peugeot 307 with corrupted valeo g0x-00 bsi , I have second bsi and it is used .
How can i virgin it just ff dump and clone flash from old mcu then adapt with diagbox ?
I extracted pin from sid 801 I think it is LLNJ can anyone check for me. Below is dump from bsi and ecu.
Hi everyone, can someone help me to do DFP OFF and ADBLUE OFF to the ECU CRD3PLUS.A0 of a Mercedes, no matter how hard I try, I can't get rid of AdBlue
Hi friends....i need to change original ecu A6461502679 (0281011928) from this car ,charging problems and no start no crank ....i have this donor ecu A6471530079(0281010835) i need info about compatibility of this two Ecu's ,or original ecu compatibility list.
Any help will be much appreciated.
THX.
good morning I did a retrofit on the w218 I mounted multibem restailing headlights I wired them up and they work but not perfectly I should code the sam f well someone did it before could help me
Hallo good people
I am looking for the virgin files for a 2018 Velar BCM/GWM,I have one with all keys locked and alarm has gone off so it’s alarm locked and can’t do any key programming on it.
I'm looking at getting into chip tuning. To start with it will only be on mine and friends vehicles. These are mostly E series BMWs with EDC16C35 ECUs.
I've tried searching but the threads are quite old so wanted some up to date info.
Where would you advise starting out with a budget of around £500 for kit?
i have this Audi A6 which came without tcm so we replaced with one from another Audi but not A6 can these files be converted to fit
vin for the vehicle attached files read by xhorse multi programmer
WAUZZZ4G3DN140395 Hardware part number 0B5927156J
Part number 8K2927156G
Hardware version number H01
hello,
anyone have stg1+ for Ford Smax 2.0 136hp ecu dcm3.5 201 gearbox manual.
car have dpf more egr off
i need strong tune for this car or dyno file tested 180/190hp .
thanks
Hi who can help me with wire diagrams for this car Vin number WF0NXXGCHNJA77474
and than from the engine ecu and I am wondering this car have a transmission ecu or it is also in the engine ecu ?
I need diagram of engine ecu and if it has a TCU athan also from TCU I need to know the wires to solonoid d car has a no reverse issue
During resetting the service intervals (oil, filters, etc), somebody pulled the OBD plug out in the middle of the function and car stopped working. Remote on the key works, everything works, but car does not starts without any DTC.
Car were just at the service centre and apprentice took device to the next car
DUMP in attachement, please help
Somebody can help me with original full BDM readout (Microcontroller + Ext. Flash + Eeprom) from ME9.7 0261209068 A 272 153 44 79. Unfortunately I don't know SW number since original ECU is fully burned and not able to READ / ID it.
Car is Mercedes Benz C230 W203 Sport Coupe V6 engine with Manual Transmission.
Can someone help me with an unlock for gpec2a ecu for hptuners? I have tried to modified it by methods posted but get Controller init fail when trying to read out with hpt. Thank you
Hello everybody
need to change variant coding in ESP205_AMG. need security unlocked file of ESP205_AMG SMR-d. I have several files but all of them are locked and needs security unlock. i tried to unlock with seed calc 3.0 but it says invalid key. Can anyone help?
I am working on a big setup on BMW M57 engine.
We have actually turbosystem 30/73, R90, big nozzles and also big valves springs.
We want to exceed 6000RPM, actually we have a hardcut set at 5500RPM, I have tested a lot of modifications with a damos to edit a lot of single values limiters and I can't never exceed 5800RPM...
Does anyone have some informations or an idea of what edit ?
Good evening friends, could someone sell me an internal photo of the Canusb AGCO 2x4 clone, I am interested in knowing what frequency they use to make these clones
