Hi,
I ran into a big problem with a DCM3.7AP while doing swirl flaps off: I read the ECU on bench connection using Multiprog to make sure that i have a full backup in case something goes wrong. I edited the file but when writing, at 2% I got an error and the ECU was dead. I had to open it and write it with Ktag. I didn't make a backup with Ktag because to read it you have to solder a few jumpers on the other side so I decided to write the file from Multiprog but that file did not contain the virtual eeprom and now that I have lost all eprom content. I'd like to ask you if anyone can help me rebuild it or maybe if anyone has a full backup of this ECU if they can share it maybe it will help. If anyone has a working solution willing to pay.
[font=-apple-system, BlinkMacSystemFont, "Segoe UI", Roboto, Ubuntu, "Helvetica Neue", Helevetica, Arial, "PingFang SC", "Hiragino Sans GB", "Microsoft YaHei UI", "Microsoft YaHei", "Source Han Sans CN", sans-serif]anyone who know how to fix the judit error 106? already use the keygen 4.36 and [font="MHH Font", Calibri, sans-serif]ProsSecCo Date Time Changer . [/font][/font]
[font="MHH Font", Calibri, sans-serif]could pay if anyone who can tell how to do. [/font]
who know how to fix the judit error 106? already use the keygen 4.36 and ProsSecCo Date Time Changer
could pay if anyone who can tell how to do.
Hello, would someone possibly be able to tell me if this file is stock or tuned comparing against an original. It feels tuned and requesting 1.35 bar on data log
So while I removed all my cats the pops and bangs tune is a lot louder, which is great.
But, sometimes there's just 1 or 2 pops that are so extremely loud they almost sound like a gunshot, which is not so great.
Can this be adjusted?
Also, can it be enabled/disabled with the AC button?
I found a Xentry 2024 link on the forum (I can not find it back again, don't know why), everything is fine. The issue is that when I start Xentry, is says " no access authorization code please contact the user help desk".
This tool provides access to the advanced settings of Metso crushing equipment.
With this tool, you can enter the 4-digit code displayed on the monitor to unlock and access the advanced service settings screen. It will generate the correct key to unlock the monitor.
I Have PP-Performance Tuned G63. I Have Genuine KTAG, i have the KTAG Tuned File. Anyone can Edit the File an do VMAX Off and Pops and Bangs? Of course i Pay for it.
Hello everyone, I have a question, I have a ready-made tune from my car, edc17c09, and the car arrived with exactly the same config, exactly the same model. Can I write my firmware to it? Or do I need to do some manipulations with the firmware?
BMW e70 ,3.5d
I have a 2007 VW Touran that starts fine but when it warms up it doesn't start, it acts like it wants to start but it doesn't start.
ecu BOSCH - EDC16U31/34.
Hello dear friends
I hope you are having a good day
I have a BMW E70 with CAS3+ and I need a complete file for CAS3 (eprom, flash)
Cas part number: 61.359147222-01
IC number: 0L15Y
5WK49514XBR
Help me please
Hello, dear members I have an issue with a8 3.0 tdi 2014 facelift, car only starts after battery recconnection. First time after battery connection car starts normally then I only have ignition. Only errors in engine ecu are p061500 starter relay and dpf soot accumulation. I swapped relays, checked fuses, grounds. Did anybody have a similar issue... Thanks in advance !
![[Image: page.jpg]](https://machinecatalogic.com/wp-content/uploads/2025/02/page.jpg)
