I am working on a big setup on BMW M57 engine.
We have actually turbosystem 30/73, R90, big nozzles and also big valves springs.
We want to exceed 6000RPM, actually we have a hardcut set at 5500RPM, I have tested a lot of modifications with a damos to edit a lot of single values limiters and I can't never exceed 5800RPM...
Does anyone have some informations or an idea of what edit ?
Good evening friends, could someone sell me an internal photo of the Canusb AGCO 2x4 clone, I am interested in knowing what frequency they use to make these clones
Hi everyone, looking for help regarding a Jeep Renegade.
UK vehicle
Vin is 1C4BU0000HPE56814 Reg: FH66 FPA Engine code is EJK
Vehicle has just had clutch replaced at another garage, since has had permanent faults against all DPF Temp sensors and also O2 Heaters Open circuit or short to battery +, cannot find any wiring diagrams on Autodata, Alldata, Tech4Techs or Carmin. Has anyone got access to a complete engine wiring diagram or has come across this fault before, carried out checks on fuses etc and have live on heater circuits and temp sensors, just need to confirm circuits now.
Hi, could someone help to do odometer correction? Audi a6 c5 2003 Magneti marelli cluster, changed cluster, did immo of on ecu, but odometer shows 99999..km need change to 382227. i have read flash and eeprom with vvdi from mcu inside MC912DG128. Is it possible to adjust odometer this way?
Hello guys, got a Fiat Ducato 2.3 150hp 2020, it does it's dpf regens every 300 km, the problem is that the car throws white smoke for about 30 mins, present error is p2000 NOx Adsorber Efficiencty Below Threshold Bank 1. The car got an engine rebuild and the injectors were rebuilded as well. Any ideas/thoughts on this ? thanks !
We are a company with 8 years experience and we are offering 1 to 1 training with 247 support to teach you and guide you with all the needs yoy may have as a beginner to learn the trade.
Get in touch if your interested.
We can pass you jobs if you are in the east anglia region of the UK and even supply a starter setup for a great cost using second hand tools
Hi dears, i post this thread fro asking you if was possible to make a your onw DECOM for deutz-serdia, by reverse engineering or clone firmware. I start by saying that im not a programmer, but MAYBE i can understand something about the argument. My question is, it could be a achievable thing ?? Or i just give up and buy it for 1500 USD if im lucky ?? i hope in a good samaritan that could help me, even if i must pay for training me. Thank you for everyone that want help me.
Hi to everyone just bought a 2009 Mercedes GL 320 bluetech without ISM. The problem is the vehicle wont crank. I have C3 with 09 2014 Xentry, and also VXDiag VCX SE with xentry 2020 vediamo, etc I am kindly asking if some can Virginize an ISM and reprogram it remotely, I am willing to pay for the service..
Hello, i need reprogram engine control module on audi s5 2009y. So i connect my odis, try select reflash ecu, and odis say that im need to use SVM code input to reprogram ECU. So im dont have etka , and i need svm code to reflash my ecu to original frimware. Can someone share it with me ? p.s. Odis online.
Hi all
Has anybody had any issues with PcmFlash module 43 on EDC17cp11 to write a VBF
on a windows 7 machine?
Ive seen it work on a windows 10 machine.
Thanks
Hi friends, needing some hand with this Mirage 2023. Needing to change odometer from miles to kilometers. Maybe somebody has some working dump
it's 93c66 eeprom
Hi anybody can remove these dtc´s from this ecu
i can pay for a good file,the car is far away from me
these are the dtc´s:
P0193
P0480
P1260
P1582
P0105
P0128
P1797
P1000
I paid three sellers who sell accounts for Haynesprt and Autodata ... after I paid, there is no more account and these people don't even want to answer me ..... why ???? this is a forum and I think someone must be responsible for these scams ... If you want to mess with me and think I'm nobody and nothing, you're wrong ... if you don't solve the problem within 24 hours, I will close your forum and all illegal activities ..... like hacking servers illegally and so on ...
[font="MHH Font", Calibri, sans-serif]hello
i have isue with CCM passat B6
chip id46
i want to add a key with avdi original by OBD
i prepare a chip 7936 with CS all is ok but when begin key learning ESL unlock and the dash block and show 0-1
and stil block with 0-2
I need help with removing IMMO from the EEPROM file of a 2007 Lincoln MKX. I’m using VVDI PROG and have the file ready. If anyone can modify it or guide me, I’d appreciate it!
Posted by: justdiag - 02-21-2025, 01:02 AM - Forum: Selling Box
- No Replies
Offboard Diagnostic Information System Engineering 19.0 Activations (ODIS-E)
Price of one activation is: 25 EUR
The Program is locked to your computer and it does not work in Virtual Machines.
Beware: ODIS Engineering works only on Windows 10 or newer and only with VAS6154 genuine devices or with passthru interfaces.
Red VNCI 6154 chinese clone also works ok after firmware upgrade as emulated VAS6154. (use VNCI Manager v2.5 if you have trouble upgrading)
For other clones there is no guarantee, but they will work in passthru mode.
Download links will be sent only after payment is done by PM or email.
Note:This version uses D-PDU API Volkswagen 30.3.0
Hi, I'm installing g a used ECM on a 2015 duramax 6.6 The original ECM is fried (no comm) Can anyone sell me virgin files for this ECM? I'm using DC706 for reading and writing.
![[Image: Bitmap402.jpg]](https://i.postimg.cc/s298XW2Q/Bitmap402.jpg)
