[font="MHH Font", Calibri, sans-serif]Hello guys! I'm still a newbie I want to make a file but it's hard if anyone can help please help.[/font] [font="MHH Font", Calibri, sans-serif]Opel Astra H 1.9 CDTCI 120HP EDC16C9. [/font] [font="MHH Font", Calibri, sans-serif]Bosch Hardware Number: 1037379426[/font] [font="MHH Font", Calibri, sans-serif]Bosch Software Number: 0281012549[/font] [font="MHH Font", Calibri, sans-serif]Engine Type : Z19DT[/font]
[font="MHH Font", Calibri, sans-serif]I extracted the file from the ecu with mpps v21.[/font]
Hello I need yours help finding SCK pincodes on these instrument clusters. Epprom24c64/24c32 I need SCK from original cluster and from 2 used ones. Can anyone help me extract pincodes SCK from this cluster dumps? Thanks in advance
Hi. This Tiguan had fault code P1736 and I replaced both sensors with OE Bosch. This code is now gone, and K1+K2 pressures look the same = good but instead I now have P176F I have no reverse gear. If I drive it in forward gears it will drive fine with all forward gears but if you slow to a stop you get an error and limp mode (or if you try to use reverse)
10748 - Clutch 2 Closes Unintentionally
P176F 00 Is it basic setting problem and are there a special guide how to? DQ500 ODL 300045R Thanks, Daniel.
Hi guys, I have pre-restyling W176 with old telematics where I put the Ntg51 online command and rear camera. Now I would like to put the original Ambient lights and make them work on the NTG5.1. I heard that it's not possible but I had read in a forum that it can be mounted. I downloaded the electrical diagram and made all the connections to the SAM as per the diagram. I encoded the enabling on the NTG 5.1 and also on the instrument panel as shown in the photo and encoded everything except on the SAM n10 which I can't find the file.
The connections I made are as follows on the Sam
B1 connector
pin 14 Blue line
B2 connector
pin 35 Green line +
pin 36 Red line +
IP connector
pin 14 + footwell Amber line
RGB ceiling light line
pin 1 Ground Point
pin 2 + Amber
pin 3 Red + line
pin 4 Green line +
pin 5 Blue line +
Suggestions guides we want some of you to talk about it and never succeeded, we share and try to get to the point.
name of the files used to encode ec ec
Hello everyone. I need a solution for AdBlue and DPF. I can't remove the Adblue warning on the dashboard. There are 799km left and the warning light is on. The car is from the year 2022 and has an MD1CS016 ecu. With MD1CS006 no problem but this is a headache. Does anyone have a solution? Of course you can pay, it's no problem. Thanks guys
hello guys hope you are having a good day
i was wondering if there is a possible way to extract datasets from any unit(power steering, headlights, etc..) from vag cars (i have odis and vcds and obd11 and pcmflash clone) or is there is a way to get them without having online access to odis or using tokens in any forum?
thanks in advance guys
Hello guys! Can someone help me? I need to fix the checksum on this EDC7UC31 file. My MMS Flex still doesn't fix it when writing in bench mode... Thanks!
Looking for help / someone who could offer coding to activate the ambient menu on a 11.2017 W213 With big screen navi analog cluster, the 891 ambient menu , car orginally had no ambient installed the chineese aftermarket module. Currently have an offer for 50euro if anyone could beat it would be appreciated
I support Programming when replacing a new Unit, used Unit for Toyota Lexus cars (SRS, EMPS, Engine,...)
If you want to do it quickly and reliably, please contact me via WhatsApp . I will help you faster.
PRICE : 50-150$ All model Toyota/ Lexus.
CAR INFORMATION:
Brand: COROLLA (SED,NAP) USA Year: 2024
Model code: MZEA18L-DEXLBA
Information on EPC
[font="Proxima Nova Regular", "Helvetica Neue", Helvetica, Arial, sans-serif][/font]
BEFORE: Many Warning Light turn on after replace SRS Unit
[font="Proxima Nova Regular", "Helvetica Neue", Helvetica, Arial, sans-serif][/font]
AFTER: All Warning light turn OFF
[font="Proxima Nova Regular", "Helvetica Neue", Helvetica, Arial, sans-serif][/font]
All services are in the attached txt file.
Please contact me via WhatsApp (informations find contact in my profile)
For urgent cases that you need to do immediately (ECU Security, Programming, 12 digit keycode...), if you send a message and there is no response, please call me. I will support within 5 minutes
Hello dears, im new to all of this. I bought a Golf 5 for experimental use only. I tried to do Immo Off on that thing, i went a lot of topic here, took some informations and now my question is. Did i do immo off correct? Can someone check for me? Im curious about. I attached Orig bin file and my "immooff" edited file.
I wrote the file with kess and it worked without any problems. Now the car won't start and you can hear the relay clicking. I tried using ODIS to see if the control unit is still accessible but unfortunately not. What is the best way to repair the ECU.
hello, I have a Peugeot boxer that won't start when cold, it spins but won't start. as soon as I connect the second battery to the engine, it starts. skeletons and batteries ok
Hi, I bought the clone VAS6154 from China in December 2024, it worked perfectly until yesterday, I put the VAS in the OBD port but no light turns on, a red led lights up behind.
When I connect the VAS6154 to the laptop, it connects and disconnects continuously with the message "USB not recognized". I have never used VCX Manager.
I mention that I did not make any update
What could I do?
![[Image: TEPORKo.png]](https://i.imgur.com/TEPORKo.png)
[/font]![[Image: fiBj0HG.jpeg]](https://i.imgur.com/fiBj0HG.jpeg)
[/font]![[Image: 4yTwo0O.jpeg]](https://i.imgur.com/4yTwo0O.jpeg)
[/font]
