Guys I unlocked SFD successfully but security acces controler refused the seed I tired (17580)(20103)(11230)(40168) for steering assist Skoda camack 2024 tried to do factory reset on angle denote because it has been replaced
Hi. I have a problem with oryginal VCI C6.
After i connect unit to software 07.2024 for Trucks I cant use it with software 09.2024 for Cars.
I am looking for info how to change firmware in unit to go back to 09.2024 Cars.
I hope for help.
Thanks
I own a shop and this vehicle got a reman engine but we have been fighting a P0017 since its first startup, engine company approved to replace the bank 1 exhaust cam sprocket and all 4 vvt solenoids. Engine timing has been manualy verified countless times. Finally i got to borrow a lab scope and found this strange pattern, for B1 Ex CMP, B2 Ex Cmp waveform matched service info. but B1 Ex Cmp did not.
Hi! I'm repairing Trafic 3 after front fire, I must to change ecu and mileage in ecu to my car mileage. Can someone help me with this? I need 55.500km because in ecu is still mileage from another car.
Hi, m8s!
This car is with locked ECU. I tried to read PIN from ECU, but the 95640 dump is damaged - only half of the PIN can be seen. ECU is Delphi DCM3.5 HY CEMO 9667175380.
I need your advice how can I start this car. The BSI I think is crypted and I wouldn't get the PIN from it. Or am I wrong? BSI is Continental 9664992380 BSI-Q05-00.
good evening I did a retrofit on a w218 year 2011 with multibem headlights I would need it if anyone has the sam f cgw files and front camera and headlights of a w218 year 2015 with multibem headlights
I have error P13C700 on ptcu calculator, I have sdconnect with vediamo and dts Monaco. Is someone here could help me deactivate it remotly I would be very grateful.
The problem is that the exhaust flap is break, so i préféré deactivate it if its possible instade of changing the part.
Can anyone make this file virgin for me? Need it to replace cluster. MILEAGE IS FINE AND DOES NOT NEED CHANGING I assumed like older F series it was just blanking the VIN but I'm told on these one of them is checksum Thanks in advance, I will leave thanks and report back as always. Thank you
Hello I tried to update Pcm MRD1
Please help with the .cff or smf-f data and software flash
Soft 6549025104
Data 6549030614
Every time make escape and write program error
Hello.
I've been researching this for a few days now.
I have an 04 S55 W220.
Dealer installed new EIS, and customer had installed their own used shifter.
Thier quote for new shifter from Germany was over 2K.
I now have the pleasure of working on it. lol
So far i have wrote Virgin Eeprom to used ESM.
What are my next steps?
![[Image: 96626073ac9fca221e828be95d064b2c.jpg]](https://uploads.tapatalk-cdn.com/20250225/96626073ac9fca221e828be95d064b2c.jpg)
![[Image: c1923d57caa0ab4d50be8bd68fd1e7d8.jpg]](https://uploads.tapatalk-cdn.com/20250225/c1923d57caa0ab4d50be8bd68fd1e7d8.jpg)
![[Image: IMG-9478.jpg]](https://i.postimg.cc/wvkMcKZQ/IMG-9478.jpg)
![[Image: Post-Instagram-1.png]](https://i.ibb.co/93Ccj3v7/Post-Instagram-1.png)
![[Image: goes-xwolf-300-mse6-ecu-tuning.jpg]](https://i.ibb.co/S4s1F14W/goes-xwolf-300-mse6-ecu-tuning.jpg)