The software number (SW) is different. According to my research, with A at the end it should still have the Bluetooth function, but there is no Bluetooth unit installed in the car. Is the HU still backwards compatible and can be installed?
This is not about component protection, Audi would keep that for me. But first I need to know if the SW: 4F0 910 732 A Model No: BE 6350 fits.
Thanks everyone for the tips and answers.
Info: Telephone control unit under the driver's seat is wet and defective. Most bus from the telephone has been bridged.
I installed Discovery Media in Passat B7 and everything is fine except for information about fuel consumption etc. I found out that the software in my meter is not suitable. I have 0407 and I have to upload 0505. I found a package of several dozen GB on the forum but downloading it with my connection for one file would be a disaster. Maybe someone by chance has a single file with this software? I would like to upload it using VCP.
Is there anyone with knowledge of Kohler engines? These are equipped with a Denso ECU, see attached photos. We want to disable the DPF, any help is welcome. We only have MyGenius, but can send up control box if necessary. Thanks
Hello, I bought Iveco Daily 2008 3.0 without dpf, but it shows P02FF error. Is it possible, that someone did dpf off wrong ? Can I just turn off dtc or it's needed to find another solution ? Can someone check my file ?
I have a k12 Nissan Micra with an Hitachi Z6 MEC93-100 ECU. I have removed and read the eeprom (ST 95320).
Can anybody help me with immobiliser off. EEPROM binary and photo links below.
I have an AUDI Q8 V6 and ECU MG1CS002. The problem with this car is that it always records error P168D00, oil pressure sensor error 3 with the engine off, I put the new sensor in for testing and the problem persists, I checked the wiring and it is perfect. I verified that the one-wire oil pressure sensor connector always has a positive 12V, when the sensor activates due to pressure it grounds, the only detail is that in the scanner's continuous mode the sensor is always activated, regardless of whether it is or not. Has anyone encountered this type of situation, do they know if it is a software error in the ECU or could it be an internal problem. Thanks
Hi to all!
I have an Opel Antara, 2.0 diesel, year 2009, with the P0705 DTC - transmission selector position sensor switch circuit, on TCU (automatic transmission).
I need help with a wiring diagram of the selector position sensor switch to test the cables.
Thanks!
Hello everyone, I recently sold my Launch X431V, and new customer has changed my email and password. Now, he needs to activate the VCI with activation code, which I can longer locate. I contacted Launch technical support, but they advised me to out to the seller, which seems. Can someone assist me?
Hello
I have Iveco Daily to change mileage
Can someone help me with calculation in BCM
Did i must reset or set same km like in dash
Now I have 396543 I need 288100
Can someoen help me and calculate this
BCM Magneti M.
Eeprom 95640
Old Km 396543
New Km 288100
So like a dummy I restored my ECU with an old back up file (using KESSv3). So now the mileage data between the dash (correct at 1024.1 miles) and the ECU (incorrect at 19.9 miles) don't match. Until the ECU and the Dash match mileage, I have an insidious-looking dashboard fault code for tampering. Can anyone possibly help me with this? Attached is the latest Eeprom file file as read from the ECU this morning. It should still show 19.9 miles somewhere in there.
Hey guys, I have w213 2017 Taxi fro Hamburg,Germany. I disabled the Taxi options in ezs and removed Taxi sign from the Headunit. Now I have error on the instrument cluster that says Some taxi functions unavailable. I searched in the variant coding of the ic213 with DTS Monaco but there is nothing to disable. If someone know with module and how should I code it I will be very grateful! Also if someone know how to disable Taxi meter in rear view mirror I will be very grateful too. Thank you in advance!
If i were to buy an emission delete bin file for a 6.7 powerstroke of the same year? And upload it using ktag what is the chance I brick the ecm? I know software can be mismatch and ID. Does this just never work? How do tuners with preloaded tunes work then? Like minimaxx?
Cześć.
Potrzebuję flasha dla BSI Continental Citroen C4 Grand Picasso 2015-
Niestety, dp5 to wyrzuciło!
Mam już uhds, więc mogę to przejść.
Bardzo pilna prośba, wypróbowałem już kilka uhds, ale nie są dostępne, jednego do tego bsi.
Z góry dziękuję.
BSI Continental 06/2015...
Nr ref. SW: 9691947780
Wydanie SW: 121.70
Licznik błysków: 1
System : B3
Aplikacja: 20
Wersja kal.: 01
Nr ref. sprzętu: 9674745380
Numer katalogowy sprzętu: 9806687980
