Hello,
We have a problem with Audi A6 2013. DTC P0A9400 , P0AB900 , P0A8F00. We already replaced the DC-DC converter. but same result. no change.
Can anyone solve this issue or make suggestions? ODIS fault code attachment.
which obd connector for use with diagzone I now have thinkdiag but it occasionally gives rare messages and when I want to read a Mercedes I better look for other software such as x-diag or ?
Hello,
I bricked a Ford Delphi MPC555 ECU (with external Flash) by using Bosch BDM adapter :/.
The part number of the bricked ECU is: 6S71-12A650-BF (Mondeo 2007 2.0 TDCI 116hp).
On internet I can not find another ECU with the same partnumber.
Want to copy EEPROM from bricked ECU to neu one.
Are there alternatives with external Flash?
br - cruuz
Here's some pictures of the LC500/h body brace that needs tightening when you hear a clunking noise when accelerating.
you have to remove the back seat, seat backs, front door sills, rear side panels, wiring loom box can be moved away a little bit to reach the hidden three bolts on the b pillar.
Does anybody have for share/sale info about SCR system on newer 2022+ Iveco daily md1cs69 with 2 adblue injectors. I need diagram on how it works and how to diagnose and identify problems by logic.
hello. i have broken golf 7 johnson control 5G1920731 (vvdi multiprog broke) dash D70F3525 and i need to replace it with another used one. i have question can i adapt any other similar dash like vdo and what is procedure to adapt it. i have just old immo data . Can odis online adapt used dash. I have vvdi2, multiprog. Thanks in advance
Hi I have read the eeprom on CAS3+ and have backed up
as well as reading the flash and saving that as well
I have done this a few times and compared them, the read is exactly the same no differences
What I see most people to is upload there file and then others read the odometer value and then give a new file with zero odometer value
What I want to know is how I can find and read this myself as well as editing it.
I have a few hex editors that will be capable what I am really after is finding the location in the hex.bin file
I had my 6.7 powerstroke tuned and deleted already. Ecm failed 2-3 months later. Absolutely no communication. I got a junkyard replacement. I plugged in the ecm to the truck because I needed to see if it is a working ecm. But derated obviously. Do I need to install emission components back to remove codes before tuning delete? Or tuning and reinstalling ecm should be fine? This is a 2016 ford f350
i have an Aygo no starter , scanner did show no com with Immo box, new wiring resolved the problem , but before that the previous garage swapped the ecu and Immo box to try also did not work for him .
i got the car, did new wiring , the fault code is gone , made full scan to the car nothing wrong , live data shows everything is normal : Immo not set , keys registered , etc..
but the car wont start .
i performed the OBD short pins method for 45 min also did not help.
according to the diagrams the immo cables goes to both connectors on engine ECU:
on the PINS to the right connector i have continuity but nothing on the left, i bridged them also did not help .
i am useless , can some one please help ?
should i post the eeprom Dump and key ID"Master key" and some one can write it back after virginize the IMMO .
Autel asks for both keys which i dont have , so the best option is to do it with Dump file.
I have an original file of a Ford Ranger. I read it. And they disabled AdBlue for me. At first, the errors disappeared. And the mileage increased, but not for long.
Good morning I have a file me 17.3.0 read with KESS 3, it is possible to extract the password and convert it to MAGPRO2,
(with MAGPRO2 I can't read the password)
Could someone explain why official Xentry passthru online + Bosch KTS560 cannot access to right or left LED headlamp module (AMLAB-L and AMLAB-R). With XDOS Xentry it works normaly.
Is is passthru VCI (in my case BOSCH KTS) or software related ?
Hi.
Could someone help me disable the Tachograph in the BSI eeprom 95160 configuration so that my instrument panel and odometer work? , or enable the speedometer function?
I replaced the entire starter set on the vehicle, the DCU102 engine unit, BSI, keys, but the vehicle from which the starter components were taken had a Tachograph.
The old flood units are damaged, flooded with water.
The car starts with the new units, works without problems, but the speedometer does not work for me.
Or another option would be to copy the starter Immo data of the eeprom 95160 to the eeprom that does not have a Tachograph,
if possible. Lexia, PPS in BSi does not offer to ground the vehicle configuration.
I am attaching the data of the eeprom 95160 with the Tachograph in the BSI, the vehicle is set up OK
even the BSI eeprom without the Tachograph, but the old Immo data does not start the vehicle
Hi guys
Can some do me favor and check the value of the first resistor on the left on this Vvdi mcu flash cable v3,on mine it’s blown and can’t tell the value.The one next to the yellow cable.
Regards
.
