Hi,
Does anyone have english damos for E90 2006 320i N46B46B 110kw? Ecu part numbers are 0 261 201 160 or 7 565 300.
I have little problem with cold starts, when its cold, under 10 degrees C, car hesitates under light acceleration first 2-3 km. Also gear shift isnt smooth because of it, but idle is perfect. It is manual. After all I changed and did, last thing is software. I think the cat warm up is too rich to run good, so I wanted take a look at this section and just a little adjust it, but I cant find it. I dont have car with me now so I downloaded some simmilar bin files and I am learning.
I would be very happy if someone could help me a bit.
Somebody have stg1 file for Sorento 2.5 CRDi? Original file attached. And if somebody have map pack for this im glad
HW: 0281011283
SW: 1037367308
VIN nr.:
SW ver.:
Spare:
Engine:
HW Ver.:
SW upg.: 1037367308
Installation:
I got an issue with Bosch 8.0 ABS that is currently on a RV.
The old abs unit is water damaged and the new used one is showing configuration fault since it says coming from manual transmission and the rv is automatic one.
My biggest question if its somehow possible to change the config on these Bosch 8.0.
I'm happy to pay for the help. The donor ABS is mounted on the RV. I have communication with one machine but not another so i am little confused.
Does anyone have original file for Renault Twingo II GT - 1.2 turbo (it's not TCE).
ECU: SIM 32
I have ecu with bad tuned ECU, so if anyone have Stage 1 for this car, I'm interested.
Already tried attached "back to stock" map, from the tuning company, but car seems much slower than stock should be. Can someone check is it ok map for this car?
Thanks.
Another workshop touched this VAG Seat 2018, Gas, MT, rear sensors only, TPMS by sensing wheel speed only; after replacing the electrical power steering. Following a replacement of the electrical power steering, it seems there were complications with the position sensor. The workshop modified the coding on several modules using VCSD (codign / adaptations) but unfortunately, they lack a clear record of the exact changes made, and there is no backup available.
I took the case and after coding 003 ABS/Brakes on-line using ODIS-D 24.1.2/6154A I am still having a bunch of DTCs. in addition to TMPS, AutoHold, ParkAssist I have a DTC on 003 (U101400) saying "Control Module Coded incorrectly". Only from ODIS-E you can also read: "FCAN Mismatch between bytecoding and Lenkerpostion signal".
The other modules have returned DTCs related to Databus error value received.
I am concerned how reliable the online coding proces using ODISD was in the way I did. PErhaps some prerequisites form other modules must meet in order to bring the right coding? i.e. What if coding on the 5F Information Electr module has a diferent car Model (equipment) configured on bytes 0-23; should it be fixed before asking to code 003?
Should I re-code several modules on a specific order using ODISD On Line? Are there any other factors afecting the comming coding from VAG. My initial expectation was to make it work based just on the VIN; however, it appears that ODIS seems to gather information from the network and relay it to VAG during the coding process.
Do you have any additional suggestions? I do have a lot of resources here including ODISE 12/ODISD 24, VCSD 24. If I had the complete decoder for 003 I might figure out what to adjust manually but I am still looking for the "official" or ortodoxe solution.
Posted by: inhosik - 03-04-2025, 12:25 AM - Forum: Selling Box
- No Replies
Hello, I offer full installation of the PIWIS 42.400.037 38.250 software along with stable drivers for the Original VAS 6154 6154A 6154B interface. The vas cable can work interchangeably with ODIS and PIWIS. The software is for Windows 10, a full HD 1920x1080 is required. After purchase, you receive full installation instructions and support. Finally, I am connecting with you to install the drivers for the VAS interface.
PRICE - 300 EURO
contact PM or
WhatsApp - +48796102116
can someone help please with immo off for this ecu? 03C 906 032 T I wanted to clone the old ecu but I didn't see that I didn't have the date in the eeprom.
Anyone recognising this modification? This is Me7.5 from 1.8 T Alhambra. I have issues with this ECU, car losing power randomly and nothing responds, throttle etc. for different amount of time, 3-5 seconds and restore to normal operation by itself. Nomatter if drive slow or under load. No error codes stored. MPPS shows programming attempts 0. Can't make propper log file because when this occurs - diagnostic is disconnected. Any advice what to look for or should search new ecu?
Upa USB S , has very little use, purchased from mikorel on this forum but unfortunately without login details for updates. May be possible to register with elrasoft direct.
Price is €180
Hi friends, I need immo off tested for vw caddy edc16u34 if anyone can help me I would be very grateful.or eeprom in attachment read in bench with foxflash.
many thanks in advance.
greetings from Croatia.
This is my 1st Used BMW dme, I was asked to clone. The old dme is dead, no comm. Can the isn & vin be changed with ista?
What are my options programing used dme?
Hi
I had to replace the esp unit. Bought same hw number part but newer sw date. The new one is post 2015y so that it does not match the collision assist etc. I have the old esp unit and it works most of the time. Would be best if there is tool to read data from it and write to the new one. I'm not reffering to coding but to the software (flash). Have dts/viedamo but I'm not sure if this is doable? Writing for sure, but don't know how to read the data.
