i am having issues with a car where we only need DTCs deleted, car has no problems beside of DTCs.
Mitsubishi L200 1M41 Denso SH7058
DTC u1100 u1101 p0605
Alguien podría ayudarme a desactivar inmovilizador a una Mitsubishi Outlander 2006 con etiqueta 8631A117 E6T45578 aunque en la lectura con ktag dice que es un E6T49 Adjunto lectura con Ktag de procesador MH8303F. De antemano gracias
Hi all member I need ECM AUDI Q7 2009 4L 901 401 Q EDC 17CP24. But this ecm high price !please all member tell part number can replace it ? I want use EDC 17cp44 or edc17cp44 !
I was hoping to get some help with a bit of a strange issue I'm having with my 2022 model EQE 350. The 12V battery died completely out of the blue, and I'm not sure how that happened because everything was normal. I've already replaced the battery, but I'm still a bit puzzled. The Xentry checks showed that the N82/2 BMS control box detected an accident with a Fusi-lock error, but there wasn't actually an accident in the vehicle. It's been sitting in pre-charge mode since then.
I'm not sure what to do to get out of pre-charge mode and activate the high voltage battery again. I would really appreciate your help!
Here are the errors I've seen;
- P0AA100 The contact 'Positive terminal' of contactor A in the high-voltage battery is jammed closed._
- P0AE2FA The switch 'Precharging' in the hybrid/high-voltage battery module is jammed in the closed position._
- P0AE2FB The switch 'Precharging' in the hybrid/high-voltage battery module is jammed in the closed position.
- P292D00 Contact 'Positive terminal' of contactor B in the high-voltage battery is jammed closed._
- P1C80FA The high-voltage component lockout is active._
Posted by: tudyshay - 03-03-2025, 06:12 AM - Forum: Selling Box
- No Replies
Hello! I’m looking to sell a couple Bootmod3 (BM3) licenses for different engines: N20 / N26 , N55, B46 / B48, B58, S55, S58. Don’t worry if you don’t see your engine code here, i’ll also update this list daily so keep an eye, this what I have atm!
These licenses will be transferred to your own email.
Each license for any engine costs $200.
Due to the amount of orders I get my preferred way is crypto but if you have an alternative, please let me know, maybe we can work it out!
Also, if you’re interested in buying multiple licenses I can offer a discount.
If your car is newer than 2020 make sure your ecu is unlocked, if it’s not you can’t flash it with bootmod3.
If you’re / ‘re not satisfied with my services please leave me a review down below.
PM me if interested, I can provide any type of proof of ownership. Thanks! Steps for transfer listed below, borrowed from a post:
To keep things smooth, you as the buyer should do a couple things:
1. If you haven't already, sign up for an account on bootmod3's website.
The email address you use to register will be the email address I enter when I transfer the license to you.
2. Buy a compatible ENET cable
You can either use the android app or a laptop. If you have a laptop with no ethernet port, you'll also need an ethernet to usb adapter (you’ll need this too for android, a ethernet to usb c adapter)
3. Download and install the BM3 OBD Agent.
4. Connect your car to the bootmod3 servers (this needs to happen for the system to allow me to successfully transfer the license).
You'll hook up the cable to your car and computer, run the OBD agent and it will talk to BM3's servers. (There are brief instructions in the link above, or there are many youtube videos on how to do this... it's very simple). Once you've done that I can transfer the license.
Hi guys any ideas on where to start looking for a problem on central locking that locks with the remote and then unlocks by it self immidiatly all doors are properly closed
Hello guys so i need to change my engine on my e46 330d 184hp 2000" its a 5 speed manual but the engine im looking at is an automatic my question is is there anything i need to change on the engine to fit the manuel transmision or is there nothing that is different on the engine it self?
Hi everyone,
I have an Orange 5 programmer with Kline adapter.
Is it possible to connect to a Ford Bosch airbag ECU with TC222
by Kline please?
Any help would be much appreciated.
Many thanks,
Jules.
[font=Roboto, "Helvetica Neue", sans-serif]good evening everyone, I'm going crazy near a Renault Modus, I would like to know if any of you have had the same problem, on this Modus the p0638 error of the throttle body appears, and the anomalous voltage error, the car runs well for a few days and then the problem returns, I put a new throttle body and new alternator[/font]
I have a range rover evoque 2019 with transmission problems engine starts but as soon as I try to put the car in D or R or even neutral the gear i try to put on the rotary switch will blink and i get faulty transmission.
I scanned the Transmission module I got only I fault
[ P1707-72 ] Transfer case neutral or park/ indication circuit.
Peugeot 307 SW 9HZ 1.6 HDI 109 hp. It cranks but doesn’t start! Error P0335 - Engine Speed Signal Absence of Signal or Incorrect Signal.
The following parts have been replaced: • Crankshaft sensor (both a new one and a used original one) • The magnetic reluctor ring under the crankshaft pulley • The fuel pressure sensor on the rail
Live data on the diagnostic tool shows engine RPM while cranking, but there is no synchronization between the camshaft sensor and the crankshaft sensor. The timing has been set correctly twice.
What am I missing? Should I redo the wiring from the sensor to the ECU? But I don’t see the point, since the diagnostic tool reads the engine RPM.
Ford transit bcm BK2T 14B476 XX
Could some help me to locate eeprom on pcb or tell me where immo and key data is stored. I have full read of flash and data flash and want to just transfer immo data from donor bcm to another bcm to test some circuits with the intention of building a test bench rig. Thanks in advance
I had to reset the device to the factory settings after a failed update.
Since then, the device no longer displays a serial number and I can no longer start an update or a diagnosis.
In the “About” menu it shows:
Device name: CRP919E
Serial number:
In the “Version” menu it shows:
BOOT: unknown
DOWNLOAD: unknown
APP: V1.09_2.21
SYSTEM: YQ_V102_014
I have already tried without success:
- shut down the device to 100%
- Changed the network setting to another network
- other factory settings (via the menu)
- tried to reinstall the apks (there are videos on the internet showing how to get into the system and gain access to the file system)
Whatever I tried, it didn't work, when I check the files on the system, there is no firmware file for the
device to reinstall the firmware and there are no launch car brands (the device is empty).
Maybe someone with more knowledge can help me troubleshoot this.
Hello, I have an Iveco Daily year 2014 2.3 diesel in the workshop, a mechanic performed welding on the vehicle with battery terminals plugged in, I changed the BSI for another and canceled the immo in edc17c46 with starter relay and it starts fine but the dashboard gives me an engine temperature error and the lights flash, is it possible that the dashboard is broken? or bsi pairing?
rgds 2 All,
the patient is x253.915 with locked mrd 1.42 ecu from 21.11.2022 running in bootloader, so all sw is invalid
W1N2539151G034807
some workshop played with it because of adblue problem
so now need correct numbers for reprograming
mb part no: A6549009600
hw: 6549017600
boot sw: 6549041300
Hello! W212 2014 hu45 , languages Korean and English in menu, ECE languages required, coding to another language is reset to English after reset! who will tell me the solution? pn 2129009026 HW 2129018506 SW 2129023309
hello ive done a chip swap on this volvo but getting checksum error im wondering if some one can please checksum the eeprom file for me its a 95040 chip an ive attatched the file thanks in advance
