hello,
need help with dpf off pls.
i have a citroen c-crosser 2,2 diesel where i need to do a dpf off.
read with kess v2 obd but my davinci can´t do dpf off.
ecu is bosch edc16cp39 (same as peugeot 4007 / mitsubushi outlander)
[font=Inter, "Inter Fallback", sans-serif]Hey guys, I have a Toyota Camry 2007 Hybrid, I recently replaced the Hybrid Battery and after replacing the battery the car did run for few days and could not go to ready the next day. I left it for some days and when I came back it when to ready and ran for the whole day.[/font]
[font=Inter, "Inter Fallback", sans-serif]When the car sleep over night the next morning same thing happened, it will not go to ready again.[/font]
[font=Inter, "Inter Fallback", sans-serif]This Car is keyless.[/font]
[font=Inter, "Inter Fallback", sans-serif]I took it Toyota dealership and they replaced the 12V battery still the problem was not fixed.[/font]
[font=Inter, "Inter Fallback", sans-serif]I don’t know what is wrong with it. It shows ready this morning and when off, that happened twice and same thing again.[/font]
VIN: JTNBB46K173015971
[font=Inter, "Inter Fallback", sans-serif]Any help please.[/font]
Hello colleagues,
I have a question regarding a 2018 Hyundai Tucson.
I'm facing an issue with the AHS (Active Hood System) module, specifically with DTC B1809.
I'm using GSD to code the CLU, which currently has the code 1C40. I would like to know if it's possible to obtain a coding option for the CLU where the AHS feature is not present.
My only goal is to disable this option after replacing the fiber cable, as even the slightest impact triggers the system, which, in my opinion, is highly impractical.
I would rather pay for this code than have to disassemble the entire front bumper again.
Thanks in advance!
Looking for a SCR off solution for VAG DCM6.2. I have already tested several versions. So would be good if anyone has a tested solution here. SCR unit is plugged of. Car shuts of after 500km and SCR light turns on. Start is refused.
DaVinci was also not working. This was also tested already. Also attached.
I have already read that this ecu seems to be tricky for this problem.
Have a nice day, please. I read immo off or emulator everywhere. I'm wondering, is there anyone out there who can IMMO OFF. Nothing is just like that! P.M
I'm trying to install a new (not used) Airbag module on a VW Tiguan 2018. I need help with online programming and coding for this part.
The person who helps me with these online tasks on Volkswagen vehicles has been having difficulties lately doing these jobs. First, he started demanding that the parts be 100% new, and now, they can only be purchased from VW with an original invoice with the VIN.
I wonder if from now on we can only depend on buying parts from VW, specifically indicating each VIN at the time of purchase and hoping that the replacement part arrives each time.
PS: If anyone can help me with this programming, I will be grateful.
I'm sure you can help me. I changed the mileage on the dcm 1.2 ecu of a 2008 clio 3 with Renolink; But with a scan (Texa) on parameters I see two entries 69/73 Mileage last reset zone 1 229240 70/73 Mileage last reset zone 3 229260. What do these two parameters refer to? Sorry for my english
Hey guys,
It's been a long time in the BMW unlock scene, and apart from Femtoevo, no one else seems to be making progress. Autotuner and Flex weren’t even around when CMD was the first to do these things, but now CMD seems completely inactive. Bflash made a great entrance but has been a disappointment for the past 1.5 years...
What happened that made everyone hit a wall when it comes to BMW MD/MG?
I have a Problem with a Dodge Ram 1500 from 2003.
I have to write the vin in an used Ecu.
What is the right software to do the job?
Can do DiagFCA the Job?
Hello everyone
I have a mercedes viano 2013.
There came airbag light / check seatbelt light on dashboard.
I read with OBD and give fault code : 9023 The component or the signal line to the component S68/2 (Passenger Seat Belt Buckle Switch) Has Open circuit or resistance too large.
I remove the seat buckle connector and put a resistance 2.2 OHM 1/4W inside, then the fault code switch to the following : 9022 The component or the signal line to the component S68/2 (Passenger Seat Belt Buckle Switch) Has short circuit to ground or resistance too small
Do anyone know if I need to put another resistance ? If yes how much ohm? I want to be sure that the problem is in the seat belt buckle.
Hi , i 've nissan qashqai with edc16CP33 ECU the engine ckrank but not start ,the ecu have 3 DTC's P0263 P0269 (ijector 1 and 2) ,P0409 EGR i tried with dtc clear by scan tool but not possible and if I unplug any sensor no more dtc shown up in ecu, as i see this ecu have comune problem with corrupted eeprom,so i return to you nissan pro to find the best solution for this issue,
Hello to everyone, can someone help me with finding long isn on cas3+ , I need to make a key for a bmw E60, i attached flash and eep from cas3,
THANKYOU IN ADVANCE!
Ecu in on Bench connected, I have openport 2 (clone) & VXDIAG VCX SE Benz DOIP J2534.
Ecu update was interrupted, can't read DTC, but at least Autotuner work wirk OBD mode, but AT don't have full factory files, only calibrations.
I will pay what needed.
Hellou can anyone help mi i need virgine SIEMENS SIM32 Eeeprom and Flash. Thank you so much. Here is eeprom and flash dump. Original ECU is deadh,this is dumps on new ECU.
![[Image: giveup.gif]](https://www.digital-kaos.co.uk/forums/images/smilies/giveup.gif)
