Hi. i have EDC16CP31 from MB i tryed to find posts about cloning one but this are quite dated and technology changed a bit hence thaught ill ask question. so story is i have defective ecu but manage to read it in bench file 2MB i assume eeprom its in it from what i understand reading prev forums. now i have donnor ecu same part no HW and SW exacly look a like. is it enough to transfer flash on bench or does it have to be BDM. FOXflash seem to read int and ext flash where multiprog flash only. what are sugestions on that one?
I have dtc p1676, p167b regarding invalid injector data.... could someone please just delete these codes as the car is rev limited to 2600rpm.
I have tried wiping out the injector data coding and then re-entering the injector codes and this succeeds and writes to the ecu but i am still unable to clear the above dtc codes.....
car is running fine but like i said will only rev to 2600 rpm with my tuned file as its coming back with invalid injector data.
hello friends, I have been doing basic locksmith tasks, but recently bought more tools to be able to do AKL situations. When is it needed to delete immo ? in what situations ?
I need to remove some DTCs in Peugeot 3008 but ECU MD1CD003 have new tunning protection. It is possible to adopt used older ECU to this car by remove immo? For experimental purposes I bought not locked MD1CD003 from peugeot 208. Will be enough find correct software and remove immo?
Hello, I have a request if someone could check the mileage from the engine ecu, I suspect it has been rolled back, the car now has 217,000 on the clock, thank you very much for your help
I need some help, if someone could help i would really appreciate cause I am stuck.
I have a windows 10 64bit laptop.
I bought from aliexpress a PSA VCI[font="TT Norms Pro", "Open Sans", Roboto, Arial, Helvetica, sans-serif, SimSun] J2534 [/font] in order to use it with my Citroen C5 model 2007.
I installed the PSA VCI driver and when I open the PSA VCI application the adapter seems to be recognized. Also it shows that I have license for PASSTHROUGH and PSA.
I also installed diagbox v9.85. The adapter looks like it is communicating with my car correctly.. when I enter diagbox v9.85, I choose my car model, I specify the VIN number and then I choose lexia application. I specify the RPO number and nothing happens.. I press lexia again , I wait some minutes but nothing. Also if I press the second option Scantool also nothing happens.
So i don't know whats happening.
In this video https://1drv.ms/v/c/a676326eca12099c/EZi...q&e=oRs7ue I recorded my screen to show the process. If someone knows whats happening and how to fix this I would really appreciate it.
Hello everyone, i am facing a swap from 1.9 TDI VP AFN to 1.9TDI PD BLS with EDC16U ecu, the engine to swap is from a seat, the seller left whole wiring harness on the engine but cutted the cabin part so if its possible i would like a electric scheme for get all the needed signals for make a standalone wiring kit, or in alternative i have a wiring from golf 4 1.9 ASZ and ecu, but the problem with this is the crankshaft position sensor so i ask if there is possible to convert in some way the signal in edc15p+ ecu for make signal from inductive to hall(thing that maybe not possible...).. and the last problem is the speedometer sensor from the gearbox that in this gearbox not present so i dont know how to adapt the speedometer to work with the manual 6+1 gearbox... thanks in advice... and sorry for my terrible english...
hello
i have opel astra H 2006 with ecu mt35e and needs ecu swap
i tried everything, carprog, fvdi, kess, flex etc
none of them could read the eeprom
who can install opel online software(not sure whats its name) and adapt the ecu ?
can someone please translate the cable pinout please
only consistant wiring i can find is that the yellow wire is reset
others seem to change from mcu to mcu
HI .. after a successful update from 26pin gw to 20pin, I have a problem with error 02001 that I can't solve at all .. ACC is turned off in all modules, even in GW in the installation list, but it still gives me error 02001 in vcds (I delete the error and it comes back after a few seconds). Car is a6 c6 and I don't have acc (ordinary css that works properly).
No other module has any errors related to acc. any suggestions on what to do??
tnx
Address 19: CAN Gateway Labels: 4F0-907-468.clb
Control Module Part Number: 4F0 907 468 N HW: 4F0 907 468 G
Component and/or Version: GW-BEM 5CAN-M H06 0035
Software Coding: 000003
Work Shop Code: WSC 00046 123 12345
VCID: 3A716F2AB55F90561D-806E
1 Fault Found:
Hello , have a vw with mst2_eu_vw_p0231d 0663 , and emergency update error, posible to flash same firmware on top?,because when it starts show me N, looks like cannot flash same firmware ..May be posible flash with odis ? Or what firmware i can use it on top ?
Thanks
Hello everyone, i have a Golf MK5 1.9 TDI BRU 66kw with EDC16U34. I bought it with "some" software from "some" chip tunner. Im really curious what actually happening inside that car. Does anyone has a original ECU file for this car?
Hello,
I need help with the Alfa Romeo.
The learning values of the ECU were mistakenly reset. Now the car no longer starts. Unfortunately, Alfa Romeo dealer could not help me either.
The starter turns, but the car does not start.
Thank you
maybe someone can help me, or a full backup
![[Image: 2.jpg]](https://i.postimg.cc/YjcZHXPS/2.jpg)
![[Image: 3.jpg]](https://i.postimg.cc/7PpZhq85/3.jpg)
