Can somebody help me to do stage1 for my original backup please?
I have a stage1 file but it is for 03l906018NP 9978 dieselgate version.
I wish to export stage1 to the attatchment. In the pre dieselgate version in the attatchment.
Hello,
Can somebody please help me with Stage 2, DPF off, and EGR off for my Land Rover Discovery IV, ECU SID204?
Read with Foxflash
I don't want to brick another ECU.
I'm having a problem with the ABS coding on my Seat Ibiza. The problem started after I replaced the starter kit. I didn't think to check the old code. The problem with the vehicle is that the speedometer was dead, which is why I replaced the starter kit.
I've read other forums and tried several codes, but it doesn't work.
I have the VCDs.
The VIN for the base vehicle is this one: VSSZZZ6JZDR055594
And the VIN for the new starter kit is: VSSZZZ6JZDR191546
My ABS unit has the reference number 6R0907379AD
ABS8.2 front H03 001
Can you help me please?
Hi all, I need disable xdrive on my F10 535 as well as the system to remove the vtg fuse via Esys or ISTA is there a way to be able to disable the xdrive
no errors on dash ?
I had crashdata stored on airbag ecu, i recently bought crashdata removal online but i still have fault code on crash detected.
Is there anybody that can look at file and see if it is removed? The supplier says crashdata is off
hi, 525 e61 130 kw i put 216 injectors and 219 nozzles, now car have a lot black smokes anyone can help ? car already tuned before, for working solution i can pay. Thanks
Does anyone know the walkthrough on how to program and code or adapt the aftermarket headlamps on a 2017 MB E300? I tried to do it with autel and realized the aftermarket headlights do nor have the QR code.
Does anyone have the step by step guide on how to do so?
Im looking for mercedes edc17 damos other than edc17cp46. Several different would be great. So I could study those. No matter what vehicle those are from.
If you upload file with password, maybe save time for both of us and send password to my inbox same time you upload. I will give you those thx and rep.
I got a pin with serialnumber GAVS20L2LVPDF6 read by obd but IT doesn't work.
Hu447 Model No VIS
Part number
447 901 0608
I found many posts about this problem but couldn't find a Solution.
Some people did read dump on there ones but Not pin there
Even Mercedes Said that providing anti theft Code is Not possible.
I have a 2014 Porsche Cayenne that had a severely damaged ECU/DME that was shorted internally (power to ground shorted through the board layers and the car would immediately blow the ECU fuse).
I managed to get the short cleared by drilling out the damaged/burnt areas on the board and got the ECU to read on the bench using X431 IMMO Plus (also tried KTAG but that would not detect the ECU). The X431 IMMO Plus indicates that I need us the cloning feature in the Porsche vehicle section, but that list doesn't seem to support the MED17.1.6 ECU. I was only able to read/backup the data using the generic Bosch MED17 function.
Read both the Flash and the EEPROM, wrote both to a used ECU.
The car would not start after ECU replacement, but I managed to get it started after using the Immo Remove function in the X431 and creating a new Flash file. However, after the car is started several times, I lose all communication with the ECU/DME
When the cloned module is installed, the car will start but I get the following codes:
DME
P160A00 Control Unit Fault (I suspect this is due to a back checksum?)
Front end electronics module
805008 Digital Control electronics (DME) confirmation failed
After a few start attempts, the DEMO shows no faults, but every other system in the vehicle shows a fault for loss of communication with DME. So it looks like the DME/ECU is getting blocked wither by the gateway module or is getting bricked/blocked by the BCM.
The only way to get out of this state is to re-write the ECU/DME with the backed up data again, in which case it goes back to starting but showing the same error codes, and then ultimately getting locked out.
Any suggestions on getting a good BIN file, or another tool to try cloning? The old ECU will not read in the vehicle, so bench reading is the only option right now.
If I were to remove the TC1797 chip and transplant it to the new/donor ECU, would that solve the issue? It seems like that would be a major pain in the butt to do, and I really don't want go that route until I exhaust the easier options.
I attached the Flash and EEPROM bin files, as was as the patched "non-immo" Flash file. The "non-immo" is the one that briefly works, but then stops and nothing else in the vehicle can communicate with the ECU/DME.
xhorse immo file creator
given CS code and Vin number (KeyID if available, if not just put F's)
result is Immo file that works on vvdi2 or any device that uses same file format
Tried it and works fine.
I want users to try it and give me feedback on it
thanks and rep
pm for pass
Hello guys i need some help on that one. Friend just changed motor and gearbox the car is OK working great but got P0010 error on it. He tried another ECU and there is no error on it so it's an ECU problem. Can somoene give me the pinout ? OCV+ and VVT ? If u need picture i can give you one i will start to check if i can see something weird.
Another question if there is not mechanical problem can we just DTC OFF on it ? I can drop the read if yes thanks !
HI to All! Have trouble whit fiesta 2011 USA cluster CE8T-10849-AC and ecu EMS2205,lost sync,need help or paired dumps.Trying initialize whit Ids and Forscan and no result...
Hi,
I have a Faraone Elevah 50 Move and I have a problem with it. I need a service manual for it with diagrams and a table of error flash codes read from the LED.
Help me please.
Hello!
i have an f48 12.2017 and i retrofited the lci model fron bumper with led fog lights.
i added SA51A option in fa and codded the bdc but i have error for both front lights. any ideas on how get the warning off? willing to pay for service.
