Hello i have a BMW E70 edc16cp35 and cas3+ which is a crank no start.Problem with car start after dead battery and jump start.I tried to sync without sucess maybe isn i corupted.If car ecu is on its place with connector atached the car turn on ignition but cant move gear selector.If i remove ecu plug and turn ignition on i can move gear selector.Atached ecu and cas eeprom.
Anyone out there got any solutions for crash data delete on a 98820-6en3a. i dont have anything to ectra the data in the sak-tc322ls. After i would need some way to clear it lol
I have an BMW x5 the ECM wast lost original file. I get an donor ECM read file an changed the EEP and Flash Write car ISN and VIN put an car the car star normally with some errorr i online program an code the ECM with Autel. All DTC get off only the 1F2108 on ECM and the velocity was limited on 30 Km/H
I read some posts about this error and can do off by EEP from ECM i post here the Flash and EEP but the limited speed was because this error ..
I have an BMW x5 the ECM wast lost original file. I get an donor ECM read file an changed the EEP and Flash Write car ISN and VIN put an car the car star normally with some errorr i online program an code the ECM with Autel. All DTC get off only the 1F2108 on ECM and the velocity was limited on 30 Km/H
I read some posts about this error and can do off by EEP from ECM i post here the Flash and EEP but the limited speed was because this error ..
Hi everyone. I bought q2 from auction and i’m having transmission problems. I guess transmission or control unit have been replaced, because trans CU mileage says 100k km less than what’s on dashboard.
Anyways, transmission had “hits” when downshifting, so we added some oil and did “Basic setting of transmission” and now it has hits when upshifting sometimes and clutches slip. I just need to know if this transmission came with car and what software should it have?
Vin is WAUZZZGA3JA018713 and photos are attached.
Also double clutch fast adaptation won’t start at all. P0731 and P0732 was happening before, output speed one appeared after basic setting of transmission when clutches started slipping.
What should I do here? i have vas5054 and obd11 with me. Thank you
---Latest UPDATED Version - 148 DLL's - Instead of Previous Version 134 DLL's as in Other Post's & Forums
- It contains 134 DLL's from Previous Verion (Svvag2000) + EXTRA 14 Alientech DLL's added by me !
-148 In Total + Updated Checksum Correction Supported ECU List !
Pass in PM after Thanks + Rep
PLEASE NOTE ! If you are a Memeber of this forum , and Never Helped the MHH Comunity *other users) with Nothing (Free advice, free Ori file, CHk, Etc; )EXCEPT Paid 4 services in Selling BOX , then DO NOT ask for Passwork as it WIll NOT be given !
ALSO - to Those who are here on MHH and never contributed with anything and just Begged for free help I MAY NOT give you the password!
If you do not have too many Knowledge'es at least you can-- Share your experiences Here on MHH with others ! -Eg/Ex;(A member with account created 6mts/1/2 years ago and no contribution/experiencences shared will NOT get rhe password!
So we will all Help each other! Togheder we will be Stronger!
From Thursday 17/04/2025 to Tuesday 22/04/2025 (Including the specified dates) will not be able to reply to messages. Please be patient. Will reply from Wednesday 23/04/2025
I got an OBD interface called VAG DS - Dual-K + CAN and I would like to know if someone knows, which is the latest VCDS version working with this Device.
One question I have an original tcu a030 545 26 32 and it’s not working can I change to this reference a
030 545 40 32 and change the soft o neet to be the same reference?
Hi
I have strange issue .
In Meg 1.1. Using galletto 1260 in boot mode
I can read flash and write but eeprom showing error of read and when I’m trying to to do Ecu ID it’s showing all 00000000.
Car came to me for read flash for maps .
Easy can do boot mode and read flash but when I try to check ECU I’d have this issue .
hello i have working xentry 2019 i hit uninstall to install 2022 and now when installing have error and rollback
MODULE DAS-Daten-bus_basic\DAs\trees\bus\eps
Error 1316 the specified account already exist
i deleted forlder licdir with key from old but still same i know best thing is new windows but i have so much stuff here trying first like that easy way
I'm looking for a backup to restore the original file to the ECU using the Flex Magic Motorsport tool.
to restore the original file because it was incorrectly modified
I contacted support and they don't have this backup
Thanks in advance
SID 321 MASTER A3C0911230001 237106820S REVISION A 822267349
Hello everyone, i need crash data clear for this SRS Unit 77960-TV0-G020-M4 5WK44784.
Btw can i just download a file from our forum and upload it? Will it work? Thanks
![[Image: 4Ulm1UU.png]](https://i.imgur.com/4Ulm1UU.png)
![[Image: KZhw0IN.png]](https://i.imgur.com/KZhw0IN.png)
