Hello. I have many asks from my clients about GM cars conversion from usa to EU. Can anybody help me with this. I have almost all diagnostic dwvices. Thank you very much.
I have a customer that have requested an update of an NTG5 Audio 20 (W253) because of issues with a rear view camera. Online Xentry doesn't start the update at all. Takes a long time setting and enabling the Ethernet connection.
After spending a good two hours and giving up, customer mentioned they had someone install a "Ghost" immobilizer.
Can this be the issue? Is this "Ghost" immobilizer blocking the DoIP connection between the mux and the Audio 20? Or is there anything special I need to do?
can you please help with resetting DSM counter in eeprom for W164 A0002701852 due to DTC P179D85 (The redundancy system for DIRECT SELECT was activated)
Here is a dump from eeprom and PFLASH (3M25J) , read with vvdi prog
hello, have a problems with vvdi mb tool. Strugling with w204 esl emulator. im using mini elv simulator. Made all procedure as write, everything look success, but in diagnostic elv still shows not personalized not activated and started doesnt crank(ignition turning on) Tried 2 emulators. Some ideas..?
I have question about change sw in ECU. I have EDC17C74 with sw: 4075, and EDC17CP14 with sw: 9978. If I buy pcmflash module 50 for VR, it is possible just read VR and downgrade or upgrade sw if is on server by write VR back? Or is possible also on bench with module 71 (what I already own?) And do you know guys (before I buy this module 50) it is on server downgrade sw for this 2 ecu, software before dieselgate?
Thanks and sorry for "💩" questions but I'm still begginer 🙂
Can anyone help me with a 4jj1 delphi ecu, original does not work and I cannot read with ktag. I have sorced a 2nd hand one but I need to have the immobilizer removed.
Please help
Hi freinds i have P180E00 "Internal control unit reset has occurred." After transmission oil and filter change. Car start but only P GEAR WORK Please I need your help
I have crashed 2021 GLC 43 AMG
I have replaced engine, transmission, airbags, seatbelts, starter and battery terminals. When i trying to reset crash data, it went successful but value doesn't change.
Need help to start it.
HELLO I NEED HELP WITH A 2011 CHEVY SILVARADO 6.0 GAS I NEED THE OXYGEN SENSOR CODES REMOVED AND ANYTHING ELSE THAT NEEDS DONE FOR THAT JOB.OR IF THERE IS A SOFTWARE TO DO THAT
DELCO E78
HARDWARE #12639237
SOFTWARE#12640467
SOFTWARE UPGRADE#12639922
THANKS GUYS
(03-30-2025, 05:52 AM)dieseltech123 Wrote: HELLO I NEED HELP WITH A 2011 CHEVY SILVARADO 6.0 GAS I NEED THE OXYGEN SENSOR CODES REMOVED AND ANYTHING ELSE THAT NEEDS DONE FOR THAT JOB.OR IF THERE IS A SOFTWARE TO DO THAT
DELCO E78
HARDWARE #12639237
SOFTWARE#12640467
SOFTWARE UPGRADE#12639922
THANKS GUYS
(03-30-2025, 05:52 AM)dieseltech123 Wrote: HELLO I NEED HELP WITH A 2011 CHEVY SILVARADO 6.0 GAS I NEED THE OXYGEN SENSOR CODES REMOVED AND ANYTHING ELSE THAT NEEDS DONE FOR THAT JOB.OR IF THERE IS A SOFTWARE TO DO THAT
DELCO E78
HARDWARE #12639237
SOFTWARE#12640467
SOFTWARE UPGRADE#12639922
THANKS GUYS
(03-30-2025, 05:52 AM)dieseltech123 Wrote: HELLO I NEED HELP WITH A 2011 CHEVY SILVARADO 6.0 GAS I NEED THE OXYGEN SENSOR CODES REMOVED AND ANYTHING ELSE THAT NEEDS DONE FOR THAT JOB.OR IF THERE IS A SOFTWARE TO DO THAT
DELCO E78
HARDWARE #12639237
SOFTWARE#12640467
SOFTWARE UPGRADE#12639922
THANKS GUYS
ALMOST FORGOT HERE ARE THE PICTURES OF ALL THE CODES NEEDING REMOVED
Hello. I am looking for paired files from a car FIAT DUCATO, PEUGEOT BOXER, CITROEN JUMPER. SID807 and BCM, DCM6.2 and BCM, DCM7.1 and BCM, EDC17 and BCM. I need data for a new program. Thank you very much for every dump.
Hey guys,
I'm currently converting my M113 to a supercharger. So far, I have the supercharger and all the attachments. I got the pulley and belt from VRP. Now here's my question: I've installed the ME2.0. How do I get the charge air control to work? I've already considered buying the ME2.8 and virginizing the engine, but the connectors are different... does anyone have a solution, or can I just pre-pin the connectors and the software optimizer will store it in the map?
I hope you can help me a little with this.
Hey guys. I swapped engine from C Klass w203 from 2005 220 CDI (MANUAL) with 150 PS into my Clk w209 (Original, AUTOMATIC) 270 CDI. Soldered the right way the plugs from ecu ( with wirning diagram powered by my friend 😂 ). Absolutely everything is working except one thing.
The car thinks it is a manual. But there is a 722.6 automatic transmission on it. Even the transmission is working good. Here is the problem now. If I push the accelerator pedal like 1% everything is normal, idle ect but if I let my food away the car cuts off after several seconds. If I start the car, without my food on the pedal, it runs on idle like 15 seconds and cuts off.
I think because it has the 722.6 transmission on it it needs a little bit more torque in idle and I think that is the reason why it cuts off.
I know it is not a common swap but maybe here is some Mercedes masters who can help me out with that problem. I have Xentry with c4 multiplexer kess and ktag
Can I just write flash from Automatik ecu ?
Picture of the ecu from the 220cdi added in attachment
![[Image: sr412.webp]](https://dieselscan.com/wp-content/uploads/2025/03/sr412.webp)
