Hello, I have a W230 EIS from a Mercedes SL 500 AMG with two 4J74Y chips. The car starts, locks, and unlocks, but unfortunately, I can't establish a connection to the CAN bus. When I read the car with a diagnostic tool, most ECUs cannot communicate with the EIS, and I can't access it. I would really appreciate your help. Thank you!
I am trying to read a Ford Fiesta 1.6 Continental EMS2205 ECU on Bench.
I tried connecting it to PCMFlash, ID works properly but I cannot Read / Write.
I then tried using Forscan, ECU was detected and it was showing 12.7 voltage on the bottom corner of screen.
But when I tried doing Test Run SBL, a popup appear and says that voltage was only 1.3v
This is weird, since on my breakout box, it was showing around 12.6 - 12.7 of voltage.
Need advice
Ive a 2015 insignia which i need to do an adblue delete on. It wont reset despite refilling the tank and using various diagnostic tools all of which fail.
Anyone able to help with an adblue delete without the need to reset anything? Ive read it is technically possible but difficult.
Can someone help me with a good solution for adblue, I've tried a few, but some give me errors, others give me a range of 400km on the dash and on the navigation, and on the last solution, only 25 km on the navi.
Hi. We have a VW Passat 2022 in our workshop. The rear door at driver side (LHD) had gone in lock and they hade child-lock in so it couldn't be open from in our outside.
I get the panel of with the door closed and broken up the door lock. I have now installed a new lock mechanism but the door will not lock with key fob. The window is also not working from driver door switch or the rear door switch.
I think the module maybe is broken? The car is from 2022 and it feels like it whould work more then 3 years?.. I tested with the module from right side at left side but didn't work, but maybe it needs to be coded? We have VCDS.
Should we buy a second hand module and try with that? Do we need to code it then?
The fault codes we got is:
01-Engine -- Status: OK 0000
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: OK 0000
05-Acc/Start Auth. -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
10-Park/Steer Assist -- Status: OK 0000
13-Auto Dist. Reg -- Status: OK 0000
15-Airbags -- Status: OK 0000
17-Instruments -- Status: OK 0000
18-Aux. Heat -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
23-Brake Booster -- Status: OK 0000
2B-Steer. Col. Lock -- Status: OK 0000
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: OK 0000
51-Electric Drive -- Status: OK 0000
52-Door Elect, Pass. -- Status: Malfunction 0010
5F-Information Electr. -- Status: Malfunction 0010
69-Trailer -- Status: OK 0000
6C-Back-up Cam. -- Status: OK 0000
6D-Trunk Elect. -- Status: OK 0000
75-Telematics -- Status: Malfunction 0010
8C-HV Battery -- Status: OK 0000
A5-Frt Sens. Drv. Assist -- Status: OK 0000
A9-Struct. Borne Sound -- Status: OK 0000
BC-Door Rear Pass -- Status: OK 0000
C0-Act. for Ext. Noise -- Status: OK 0000
C6-Batt. Chrg. -- Status: OK 0000
42-Door Elect, Driver.
1114113 - Local Data Bus
U10BA 00 [009] - No communication
52-Door Elect, Pass.
196644 - Local Data Bus
U10BA 00 [009] - No communication
[Door electronics driver side rear function limitation due to missing message
Hello, I have w205 which stopped showing mileage. Instrument cluster is changed because HUD was retrofited. IC was taught in before. Does anyone know how to fix this? Thanks!
I managed to modify mileage on my cluster with DIGIPROG 3 but now it's write CoDE on LCD... So i think i corupted the original file from original cluster.
I have an other cluster (same one) but i don't know how to modify VIN in Eeprom M35080
[font="MHH Font", Calibri, sans-serif]i have a a250e year 2022 on my office that had a crash on rigth front side...smal crash but open curtain window. So the car not start because have many error about 30c. I cant found pyro fuse on this car... anybody can help me...I pay of course.[/font]
Good morning everyone, I wanted to ask for help with this stereo. It has already been serviced at another technical service, and it seems that the data in the memory was recorded incorrectly. I'm attaching the dump to see if it can be corrected.
I am asking for 3800usd.
the subscription will cost you $1250
to upgrade it too full master if you wish is $2500.
which is 7650usd which is a saving of $2000.
start working for $5050 instead of $9650.
The original casing was untidy, so i have replaced it.
Free shipping anywhere in ROK (South Korea) Global shipping available.
