Hey! I havent got my winols computer working yet, suffered from a hardware failure some weeks ago, and im a little slow at fixing it. I have a file from a bmw e39 530d (dde4/edc15c4) and i could use some help just running the file at checksum correction.
hello, i have question , my frend try make cruse xontrol on by elm config program , he do what porgram seys, he write samething and after few % stop , now car no strat , cant start , forscan not recognize car , red diode on dash blinking, , i thing he kill ecu , wanna help , i thing i must write fulkl backup to the ecu ?
im right ?
meaby smwbody have buckup files sod803a 5ws40736d-t 8m51-12a650-and kynd,
BMW F31 - dead, no signs of life in car, nothing works, dash dead hazards not working etc.
FEM cant be read with vvdi 2 on bench, no comms
Eeprom read is here with vvdi prog.
What is the next step, how to adapt used one etc.
Hello everyone, I have a Range rover evoque 2016, The front blower works for a few seconds then it stops, after the diag I found the error B1B72-13 LIN Bus 1 power supply circuit - circuit open, and error B1086-87 Air distribution damper motor, probably because of the LIN bus
the air distribution dont work
symptom:
- The front blower works for a few seconds then it stops
- Air distribution dont work
- Can someone help me with wiring diagram for evoque 2016, VIN SALVA 2BN1GH161193, or any idea how to proceed with LIN bus verification
thanks.
Can anyone give me some guidance in what to look for when replacing a instrument cluster in a VW Touran 2.0TDI 2009 - Engine code BMN
Old cluster is dead and I haven´t been able to troubleshoot what is the reason because far away from home.
I want to buy second hand cluster and bring with me just in case.
Do I need any matching numbers? I found a website that had a large list of article numbers for Touran dashboards.
Would any of them work as replacement. I´ll attach link.
I´ve already made immo off in ECM so starting the car should not be a problem hopefully
i have manifold full dirty and electric actuator is broken, i dont want to change manifold...need to delete swirl flaps with disconnected motor, can someone erase it?
Anyone know how to create APIM manifest to update the module
I know its create automatically when u use FDRS but it dont work and it gives USB error
So could anyone create one and help me update those modules pls
The manifest should be less size so the apim update use less files
Because 2021 2022 modules has less memory on them and can not be updated
Hello guys! Recently I did a repair on a Volvo cem module CEM L pn 30728101A. I replaced the connector that was corroded and cleaned up some bits that had corrosion but were salvageable. Car had problems with starting, sometimed the starter was working and sometimes it was not. Now i’m getiing a fault code CEM-6C48 and CEM-1D09. What could have gone wrong? Also there is 0 programmed keys showing in cem diagnostic data. Has anyone had any experience with this?
Fast and high-quality remote software installation
2–3 weeks for software testing
Individual approach
System of bonuses and discounts
We can also offer a solution for all cars, trucks and agricultural machinery.
JCB Parts Plus+ 2.00.0004 02.2017 - 80$ JCB Service Parts Pro 1.18.00001 (05.2015) - 70$ JCB Service Manual 01.2017 (need to have installed JCB Service Parts Pro or JCB Parts Plus+) - 55$ JCB Service Master 4 v24.12.2 2025 - 165$
JCB AGCO Sisu Power Wineem4 - JCB Service Tool 2.9.2 - 165$
Description :
JCB Parts Plus - Spare parts catalog for all JCB models and all markets in the world.
JCB Service Parts Pro - The electronic spare parts catalog JCB Service Parts Pro 1.18 contains a complete catalog of spare parts for all JCB models and all markets in the world. JCB crawler excavators, JCB wheel excavators, JCB telehandlers, JCB backhoe loaders, JCB wheel loaders, JCB skid steers, etc.
JCB Service Manual - The software contains factory documentation for the repair and maintenance of all JCB equipment, as well as for engines that are equipped with JCB equipment (manufactured by Cummins, Isuzu, Deutz). Device - parts-pro or parts-plus
JCB Service Master 4 v24.12.2 2025 - JCB SERVICEMASTER 4 IS DIAGNOSTIC SOFTWARE, which contains complete information for diagnostics and calibration of agricultural machinery and engines JCB. Device - Nexiq, JCB DLA, SCANMATIK 2 PRO, AGCO 2×4 CANUSB
JCB Service Master 4 v21.4.2 05.2021 - The program is a diagnostic software for working with agricultural machinery and engines manufactured by JCB. The software contains comprehensive information that allows you to carry out diagnostic and calibration work. Device -DPA5 or Nexiq
JCB AGCO Sisu Power Wineem4 - Wineem4 is an easy tool for the sisudiesel electronic control unit (ecu) monitoring and adjustment program. Programs can be used with eem2, eem3, eem4 ecu. Can bus used to communicate with ecu. Device -AGCO 2×4 CANUSB
If you have reached this line, it means you have questions - we will be happy to answer them!
Hi friends,
I've retrofitted LCI front headlight for F22, Add 552 and 5A2 in Fa and code FEM,REM.
I have FLES module in list but when I inject cafd and want to code it's finished with error.
Could someone help me?
Hello brothers, this week, until our quota is filled, we will be providing free help and support for DPF and EGR cancellations on Ford SID208 and 209. Thank you, reputation, and write only privately. Please do not ask questions about other topics. We only provide support for file modifications. Let's not waste time on topics that we can't help you with.
We tried to fix a box on an Audi A5 2.0 TFSI. We took a new box from yunkyard. We have a boot readout from Eeprom on old ECU, but couldnt get a read of flash.
Then We have boot read of Eeprom and flash from new ECU. Easiest to do immo off I think? Or can we just put old eeprom in?
Somebody can check? maybe do immo off?
Boxes has same numbers.. 8T2907115 0005, 5WP49004
All files are attached..Are immo in Eeprom or flash? or both?
