Offboard Diagnostic Information System Service 25.0.1
Price of one activation is: 25 EUR
The program is locked to your computer and it does not work in Virtual Machines.
Before you request a key please disconnect any usb drives from your system, run the programs as administrator and exclude it from antivirus ( defender) scanner.
Please make sure you select a license.dat(from patch 7z) on install of the program, if you don't then after it's registration you will get an error.
Beware: ODIS Service 24 works only on Windows 10 or more and only with VAS6154 genuine devices or with passthru interfaces.
Users reported that red VNCI 6154 chinese clone also works ok after firmware upgrade.
Download links will be sent only after payment is done by PM or email.
Hi everyone, I have a 320d automatic that mounts a bosch edc17cp02. Among the more experienced, can you tell me the addresses of the neutral torque and the parking torque?
Hi.
Please someone with more knowledge to help me with this file.
I try to clean crash. SRS nr. BHN9-57K30A
I try some solutions founded at forum but without success
HELP!
Hi mates. I need file frf, for Vw Golf VII transmission DSG 0CW 300 041 R. (on my catalog flases only ver ... 041C,D,N,S,L,Q)
Its sometin wrong, any errors in memory, but transmission changes gears at very high engine speeds and after a long while, but only up to 5th gear. 6th and 7th gears can only be engaged manually.
Hello guys, i need to make EGR OFF, UREA OFF , FAP OFF on this Peugeot 307 2.0 110hp, year 2002, i have antipollution error on dash, additive unblock diesel filter error. What can be done on this matter? EDC15C2
good morning after programming with mpps the ecu in question is blocked I can't program it anymore not even with odis engineering. could someone have a backup where I can then do alignment with odis online or do immo off if possible. thanks to everyone
[font="MHH Font", Calibri, sans-serif]Hello, I want to ask, maybe the topic is not for here, but still, I have a Saab 93, I do stage 1 with ECM Titanium, I turn off the errors for DPF, EGR, and swirl flaps, however, when I upload the car map with stage 1, everything is ok, but the error for the swirl flaps remains, I remove the errors with DTC remover.Can someone tell me where I'm going wrong? Thank you[/font]
Jeep Renegade 52180791 0285015836 i need help i wrote several clean files but it gives me internal ECU error. At first i wrote the file and the ECU worked now after 2 months it gives me this error. Now i want to try to read the microprocessor RH850 can someone show me the pinout diagram for upa?
I attach the file with the crash and the clean one without crash that worked for 2 months, I also attach the image of the error in diagnosis. Please help me because I don't think it's the ecu to replace I want to try to read the micro someone who provides me the connection diagram for UPA. Thanks to everyone
is it possible to read the controller from daihatsu sirion / subaru justy with the denso 89560-b1810 controller on the nec d70f3180gj processor. there is a similar controller in suzuki alto. would anyone have a description of the jtag connection???
Hi everyone,
I have a 2003 Vectra with the Z18XE engine. Yesterday while driving, I suddenly lost power steering assistance. When I reached a traffic light, I turned the car off—but after that, it wouldn’t start again. The dashboard lights come on, but there’s no crank and no start.
After several attempts, it eventually started and I managed to drive it home. But once I turned it off again, it completely stopped working—same issue: no crank, no start.
After reading some forum posts, I’m starting to suspect the CIM module or even the ECU. I also noticed that I can't communicate with the ECU through the OBD port.
Can anyone tell me how to test the CAN bus lines going to the ECU and CIM module? Also, if I buy a used CIM module without a key, is it possible to swap the EEPROM from my original unit into the replacement to avoid programming a new key and CIM?
I also checked the resistance on OBD port between pins CAN High and CAN Low with the car asleep and i have 61 Ohm.
Lastly, if anyone has the ECU pinout for this engine, I’d really appreciate it—I haven’t been able to find it anywhere.
Thanks in advance for your help!
Any chance someone could just confirm this solution is ok for DPF / EGR off on a EDC17C46 file, I used the switch and the 2 EGR hysteria maps with DTC's deleted inc 02 sensor.
![[Image: Bitmap4.jpg]](https://i.postimg.cc/5tg2405P/Bitmap4.jpg)
