I replaced an Ecu from a facelift W906 but the setting for manual car or automatic I can’t change. Old ECU is dead. Is here anybody that wants to change it with vediamo? It’s a paid job. I will be at the car within a hour. Send pm please
Hello, does anybody know how to remove notify on dash for open doors on audi s3 2010. I have completly swaped audi s3 in golf mk2 and car have bcm, getway, ecu, tcu… but dont have door locks and module and cant recognize that doors are closed or open. I just want remove that from the dash, does anyone have solution for that?
Dear all,
I been struggling with a project, John Deere S690 with L22, got several chips out but they are unreliable and I can not find the eepron. Anyway, trashing hours are supposed to be in another module like PTP or LC1, maybe RC1. My question is,
can I update those hours with a OBD tool like Kess 3, JD service advisor or some like that?
I think is very dangerous be taking Half of the machine chips apart to find 2 eepron and like I said, so far haven’t yet.
Need update engine hours and trashing hours.
I decided to open a thread about this car because its turning a pain in the ass.
Van came on a non start situation,the van were running and then suddenly stopped. It cranks but there is no OBD communication with no unit on the car (ABS,SRS,UCH,ECU,IC)tried with 3 diag (launch,texa and can clip).Only unit I can enter is Heater,I suppose that this is the auxiliary heater.I checked feed on OBD,all fuses,even connected an oscilloscope and the signal looks good and square. I have tested with another ECU,another UCH but it doesnt make any change. I also tried disconnecting every CAN BUS related module 1 by 1 to see if there is one shorting the circuit but no changes. Seem like this problem was before because customer told me that on another shop before the van stopped they tried to scan to reset oil service and they received no communication. So I guess that there is a problem with ECU apart,and the OBD can BUS related,so I need to sort out first the can bus one to start diagnosing the ECU related.
Also checked can bus resistance with battery disconnected and I get 61.2 ohm with everything connected,also checked internal resistance of ECU and IC and they gives me 120ohm.
Good afternoon! I'm having a problem with Sprinter vans with CRD3.xx. Many have arrived with the check mark flashing. I've remapped the DPF and EGR, and everything works, but the check mark is flashing on the dashboard (I think it's codes in the CPC). I tried scanning (before and after remapping) and there's no communication with the ECU. I checked the cables and they're all in place. Has anyone experienced this? It's happened to me in more than 5.
Hi
I have A W204 C200 2010 model. The radio doesn't want to eject the CD's which are inside and it keeps beeping writing Drive Unavailable.
Can anyone assist
Can someone check if this file is ori and if dieselgate is present please ? attached bench read from a golf 7 2.0 150p .
EDC17C64 , sw 1037533908 , 5520 version .
I bought this tool for 1 ecu. Yamaha FZ6 2007 with 2x 17 pin connector.
Bike is model 2008. But no luck. First i tried with Black PCB no ECU found... now i ordered Red one still no luck.
Is there any way to make it work? Its a personal bike so not worth it to invest much.
Hi everybody, I'm new to this forum and I have a problem with my Smart 451 keys.
I bought a used 451 MHD 2010 facelift and it came with one key. The remote doesn't do anything, but the key starts the car no problem. I can lock the car from the inside and open it from the door with the key.
My friend used Xentry to teach in the keys. But still the remote won't do anything.
Can somebody assist? I've ordered FVDI.
Any help would be kindly appreciated.
Hello i have this crafter that wont go over 110km, in vcds on client speed limit is 90km, but i cant find the login code to change it , here is flash and ept
I tried to connect magic tuner flash v3 with Nexiq 3 but without success. Tried 250k and 500k, as well as mcm or acm ghg17.
DDDL works great with Nexiq so all drivers all good.
Does any one know the solution?
Truck is Freightliner Cascadia DD15 2017 GHG17
Hello. I changed the injection of a passat b6 from Siemens to Bosch, now my shout off valve doesn't work ,and the spark plug relay too.... it can be solved from the software.... Can any 1 help me please to solve that problem ?
.
