Hi
I lost my default settings for Logan 1.0 2020 dashboard
It was renolink use to do this
Can someone do a print screen with a renolink on a same car
Thank you [font=Inter, -apple-system, BlinkMacSystemFont, "Segoe UI", Roboto, Helvetica, Arial, sans-serif, "Apple Color Emoji", "Segoe UI Emoji", "Segoe UI Symbol"]Am nevoie de niste setari din fabrica pt loganul meu la tabloul de bord.[/font] [font=Inter, -apple-system, BlinkMacSystemFont, "Segoe UI", Roboto, Helvetica, Arial, sans-serif, "Apple Color Emoji", "Segoe UI Emoji", "Segoe UI Symbol"]am umblat cu renolink si am setat ceva gresit.[/font] [font=Inter, -apple-system, BlinkMacSystemFont, "Segoe UI", Roboto, Helvetica, Arial, sans-serif, "Apple Color Emoji", "Segoe UI Emoji", "Segoe UI Symbol"]dacia logan 1.0 2020[/font] [font=Inter, -apple-system, BlinkMacSystemFont, "Segoe UI", Roboto, Helvetica, Arial, sans-serif, "Apple Color Emoji", "Segoe UI Emoji", "Segoe UI Symbol"]multumesc[/font]
Good afternoon. I have an ezs module that I need to change the chassis number for.
The processor is 1L02M.
Can anyone help me or tell me which software to use to edit the file?
Thank you.
hi,
c-zero have dtc p1b28 and no start
SRS-ECU no dtc and i think have not original file
Can someone check file srs eeprom
s25a64 read 95640
ecu 8635a317
Hello, is there any possibility I can find the wiring diagram for the gearbox plug for a audi a8L 2012 3.0tdi, gearbox ZF8HP55? It has a weird issue with the car not being able to communicate with the TCM and giving U0101 in every module when ignition is on and the gearbox can't be scanned either. But when you turn to ignition off, the gearbox and selector lever can be scanned and returning various CAN messages (u0001, u0002, u0046, u0103, p0817, p17F9). Someone before me changed the plug at the gearbox harness and i think the wires are not wired correctly, as the new plug has different wire colors than the cars wire harness.The car does not crank or start, just ignition comes on and for a brief moment you can see P on dashboard and then it dissapears. I have checked all fuses and relays and they all are in good order.
EDIT: Fixed !! It was a broken brown ground wire in the gearbox connector, pin 14, as soon as I connected it back, the engine started and all lights on the dashboard went out, also there were no error codes in the modules.
Hello, i need a solution for this citroen c5, original ecu is damaged and no communication. Bought a second hand ecu and need to make ecu virgin or immo off solution.
ECU : IAW 6LPB, CMME 6LPB CEM1
HW: 16.707.154
SW: 16.795.024
it is a 2002 ford focus c-max 1.6 tdci. I blanked the egr physically. The car has 80kw it feels really sloppy especially in lower rpms, had one with 1.8l engine and it was flying above 1800rpm, but this one just barely moves. I m going to get rid of it in a year or two so why not just get a tune I guess.
It would be nice if someone could remove Egr, add a and if possible make idle at 900+- rpm, because when you release the clutch currently at 750-800 rpm it rattles really loud.
Hi, how are you? I got this Varian code error, but I can't get the code to write it. Can someone help me because the scanner doesn't have a backup copy?
Hyundai Accent RB 1.6
2014
VIN KMHCT51BAEU160441
i have this Audi Q5 which is misbaving Front left brakes when i drive for few kilometers it start braking on the left side to the extent of getting smoke of burning pads no fault codes found in ABS module if there is anyone who experienced this problem how did you go about it i posted scan log
Hello, i have xpro5 installed on my phone. My subscription ended two weeks ago. I have purchased lenovo tablet and would like to move xpro5 app to my tablet. I have installed xpro5 app and copied cnlaunch folder to my tablet root. I have logged in to my account and i can see car manufacturers in app but it wont connect to any car. When i check update there are 3 pending updates: xpro5 8.00.214, diagbaseservice_app and vin_recognition_app.
