Yesterday I updated ic204, earlier I saved the coding using vediamo, but I didn't notice that the whole coding wasn't saved from the 5.VCD_05_Variantenkodierung tab.
My saved coding is 09 1F 1A 41 42 0B,
and it should be 09 1F 1A 41 42 0B XX XX.
I managed most of the coding, but I have a problem because my car is C204 and on the welcome screen you can see the car logo W212, and when you turn on the cruise control there is no notification of what speed it is set at. Could someone help me?
I'm planning to go buy a car far away from home that starts but turns off immediately.
Its a VW Touran 2009 2.0TDI BMN
The ECM has two dtc stored
P1570 Engine Start Blocked by Immobilizer
P1640 internal control module eeprom error
I don't have any spare ECM at the moment.
Is there any chance I could get the current ECM to temporary start the car by making immo off so that I can drive it home?
I bought some tokens to do immo off on edc17c84, they charged me 60e for immo off but it doesn't work, thinking it could be a problem with the van, a week ago I bought another immo off ecu for another renault edc17c84 doesn't work either and they haven't responded for months. My question is, has he scammed more people? It's a shame,
Hi. Has anyone managed to do immo off on Renault Clio 2001 1.5dci common rail with Lucas LDCR 80886F 8200136328--B HOM8200114683 with a flash AM29F200BB and Eeprom ATMEL048 25080NC? I tried the solution with carlabimmo emulator but the car doesn't start and gives a fault code, I spoke to them on the forum but they said that this solution doesn't work because it is an LDCR instead of a DDCR. If I remove the eeprom from the ECU the car starts but doesn't accelerate.
Hello mates!
i need to program the land rover discovery 2019.
i used to used the sdd but it does not access the 2019
i need advice and support if i can use the pathfinder or topix?
price 100usd/1pc price 250usd/multi pc Linde Forklift LSG v.5.2.2 U0296 09.2024 Service Guide Information Size:34.18GB (Winrar files)
Type of Program: Spare Parts Catalog, Parts Kits, Tecnical Documnets, Service Information, Jobs & times, Special Tools Database + Interface Languages: English (GB), Deutsch, Francais, Italiano, Espanol, Svenska, Polski, Cestina Version: LSG v.5.2.2 U0296 09.2024 OS: Window 7, Window 8, Window 10 32 & 64bit (Tested on window 7 ultimate 64bit and window 10 pro 1607 64bit) Data version: U0296_LSG_Master_202409110619 Year:09.2024
Hi, can anyone help with a corrupt abs module showing fault code U2007:46-2B Calibration/parameter memory failure please
This unit was corrupt by Autel and i have tried updates and relearn procedures with FORSCAN all were successful but it leaves this fault and the hill assist warning chimes every time the vehicle is started and the traction contol lamp is illuminated at all times
I have noticed on the module check the abs module is the only one without a VIN number and i suspect this is the cause of the warning lamp?
Do i need a complete virgin file to fix this or is it a new/used module? are these straight forward to configure?
Thank you all in advance
We have two new services for DSG and want to offer a small portion free to the mhhauto members via the public section. Upload the dumps here and we will assist you free of charge as it should be, without asking for money via PM (like some people do)
Immo off:
Temic DQ250 MQB
DQ200 (limited support).
Immo clone /transfer/modification for:
DQ200
DQ250 MQB
DL501
Multitronic VL381
NOTE:A full boot mode read of MPC/IROM (TC1766 / TC1782) + EEPROM is required!
Please don't hijack this thread with "Check PM!" posts or similar. Let's keep the help public and free!
Magic Motorsport Flex released a new OBD Solution for Chrysler Jeep Dodge Fiat Continental GPECx ECUs, specifically GPEC2, GPEC2A, GPEC3, GPEC4, GPEC4LM engine units.
Upgrade Info【Version: 7.17.0.0】:
New release on Flex ECU Chip Tuning Tool dedicated to OBD programming: a Flex OBD solution for Continental GPECx ECUs.
Just unlock the unit in Boot mode and then proceed with reading and writing the map area directly via the diagnostic port of the vehicle.
Thanks to the newest update of Flex, removing the ECU every time to modify engine parameters is no longer necessary: unlock your control unit in Boot mode and then go for OBD any other time.
Some of the supported vehicles:
Chrysler 200 2.4L 180PS
Dodge RAM Promaster City 2.4L 180PS
Fiat Tipo I 1.0L Multiair 120PS
Fiat Toro 2.4L Multiair II 185PS
Jeep Compass 2.4L 180PS
Jeep Renegade 1.3L Multijet 150PS
This new protocol is available for the following software packages: OBD
1M – SW Flex ECU (car, van, bike) OBD/Bench Master
car in problem is fiesta 2006-07 engine 1.3 with simens SIM 21
driving fine,after park the car,cant start..no milege on dash and flashing LED for immo...
OK probably dash connector so I resolder all of them..same situation..OK let start diagnostic..
cant reach engine ecu -power suply on 2 wires is fine but ecu relay not engage and not send power to PATS on ignition lock..so look in schematic..PATS have 4 wires rx/tx and power/ground.what confuses me is fact that on pats PIN 1 there is no power until engine ecu dont sent ground pulse to ecu relay....IF I manualy engage that relay then there is 12V on pin 1 pats..so wires/fuses are fine...does it mean myne engine ECU is failed or just I have no idea how Ford work...
engine ecu -pats are part of immo is it dash too or dash is just CAN connection for this two
will try few more diagnostis/check but need to know how this system work..dont understand how eng.ecu will compare transponder code IF there is no power until eng.ecu is not engaged..
i need more info..time to doing homewrok..
any help preciate !
SOLVED !!! on engine ecu pin F9 heavly coroded,somehow water came in and completly disolve that pin in connector..F9 is pin for ignition on to ecu.. orange yelow color
very good and cheap tool for that old Fords are Forscan with vlinker interace...manage to finish all programing with it..
My CD30 MP3 died, so I bought a new one. I was able to read the dump from both old and new radio with CH341A mini programmer (even if it took tens of attempts to get it read while trying to reposition the clip). Old radio security code 4707, new radio code 1283. Dumps are attached.
I plugged in the new radio, then with China Opcom deactivated theft protection on it with code 1283 and then activated theft protection with code 4707. I thought now the screen and the radio would be there with same code.
Now I've ended up in state where the radio plays music, but there's "display safe" on the screen. Both radio and TID says "ID O.K." and somehow I have now also the Security wait time active in the radio (I did try activate/deactivate a couple of times).
Hi
Can anyone help car came in to me with immo off ecu safe showing on dash cluster and flashing glow plug lamp
Audi Q7 2010 EDC17CP44 old ecu is dead from water ingress.
Old and new ecus same part number
Fault codes showing are P1570 - ecu disabled
Access/start authorisation: 02241:000 Engine Control Module, immobiliser data not adapted
Car currently starts with immo off ecu.
Autotuner backup attached.
![[Image: 25040217435792639310.jpg]](https://www.eobdtool.co.uk/upload/info/25040217435792639310.jpg)
