Hello
Mercedes W204 7g-tronic.
Anyone of You has got some tips how to remove this selection range sensor? Which should I buy if I have number 23 on it?
The fault is 0705 (Selection range sensor A has an electrical fault).
Hi
I'm looking for information on hoiw to change the vehicle's mileage. The old X100 has this model but shows a security error. Does anyone know where the mileage is? odometer or bcm?
Thanks
I need a solution for a disabled MAF for EDC16C36 Renault Master 2.5DCI. With the flow meter off it runs fine, there is a problem with starting a cold engine. I am willing to pay for a working solution. Best regards!
Problem with Turbine bosot pressure, Turbo is unable to adjust the boost. It overloads, releases and then hits again and releases.
And it is strongly felt that, it goes and does not go.
What has already been done in the meantime.
Adblue removed
DPF removed
Egr x2 plugged and removed
With, MAF without MAF the same, new, MAF the same
Intake leakage chaecke 3 times
Turbo regenerated, set on the machine - then one more time taken out and given to other turbo workshop, they checked and set the VGt other way and same
Turbine adjuster changed
Throttle replaced
MAP sensor replaced
Exhaust gas pressure sensor replaced, both shows up to 3.5-3.8 bar, disconnected sensor shows 1.35 bar the same.
Loosen exhaust pressure sensor so the ecu see less exhoust presure and same
Turbine resets done and the same
All possible resets done too, the same.
Uploading original or mod the same.
I am slowly running out of ideas.
On, original only errors from the particulate matter sensor and from NOX.
If you drive a lot, it will throw out, error under eobd from throttle valve B (P211A). But it is visible, only under eobd it is not, in DACIA diagnostics.
I am slowly running out of ideas where to look
It seems that how, the turbine reset will be done as if the first acceleration was much better but the next ones are the same.
Need dump (Micronas + eeprom 24C32) or solution for "error" display message cluster 1K0920973B. The original EEPROM dump is lost. Thank you in advance!
Hello everyone, there is e91 with error 434E Cooling air flap system, activation.
Radiator fans start up randomly i assume this is related to this error?
Can these flaps be decoded using ncsexpert?
Someone have ori file for mazda 6 2.0 2008 year? rf8g ecu . I have some and found quite lot online but all of them are quite different from mine read and i can't recognize much in these denso dumps.... there are a lot different base versions although their upgrade SW version is same....
Hi, my j-box 3 is not working with JLR SDD v167. I was curious if anyone could help. It's worked for GM TECH2, and ford FDRS so far. j-box 3 drivers are installed. Thank you greatly if someone can help.
Hi, everybody.
I have this interesting problem, on my octavia 2, I changed the cluster. The cluster from the facelift was fitted to the pre-facelift octavia. They redid the connector, replaced the immo chips in the keys. Gateway unit is 7N0... And the ABS is fine too. After the replacement, the cluster works as it should. VCDS has been coded, km set. etc... Then at home I tried to connect via ODIS and it says communication error/ cluster not found. Same error with immo. Can you please advise me how to fix this problem? I repeat that VCDS is working without any problem and does not report any error. I don't have much experience with ODIS, but I would like to solve this. And I would be grateful for any advice on what to do about it. Thank you all very much
Hello everyone, I'm looking for a functional solution to remove the EGR, DPF, and AdBlue from a MD1CS006, as we've already tried the official DaVinci, ProjectX, and Swiftec solutions without success.
CLAAS CDS CLAAS Diagnostic system - Allows you to quickly identify defects and configure and update the integrated management system.
CLAAS Parts Doc -Claas parts doc 2.2 contains a detailed and clear guidelines for the maintenance of all equipment models claas, will help the user to timely and quality care in the repair, maintenance, calibration, installation and dismantling of certain parts of vehicles claas.
CLAAS WebTIC Offlin - Gives you easy and quick access to technical information for claas machines. All documents, instructions, catalogs for this equipment will be at you fingertips.
If you have reached this line, it means you have questions - we will be happy to answer them!
can someone give me radio-code for this radio on iveco
i saw a website called carstereocode and app on apple-store but i dont know if either of them is trusted
Make IVECO
Model Daily NIS
Part/Model 5802403840
Manufacturer APTIV
Serial number T0BYD288010161
have a 2010 i30 can anyone tell me what chip transponder is in the key ? finally have pin code that works - live data says key learned but 0 keys - try to do key learn and says key invalid
- opened key up and no chip in there ,tried with a pcf7936aa chip i had from ages ago to see if it work but still saying key invalid - vehicle came in as non runner and its had ecu etc on it
have a 2010 i30 can anyone tell me what chip transponder is in the key ?
try to do a key learn and says invalid - opened key up and no chip in there tried with a pcf7936aa chip i had from ages ago to see if it work but still saying key invalid
![[Image: ID.jpg]](https://i.postimg.cc/28cKNV95/ID.jpg)
