hello guys i have this head unit that goes only black screen i order ftdi cable for rns510 with setconfig but i believe i need a dump .frg
not info detected on the head but only monitor can be detected so the usb cable works fine
1t0035680 px
hw ; h10
sw ;5274
any ideas or any help would be so apperciat it
Hi maybe someone could help with a free solution? I already paid for 2 supliers already and none of the files works. with 1 file car stalls over 2k rpm,with another file it stalls over 3k rpm. thanks...
Good day community.
I'm reaching out for help with my Mercedes W167 Hybrid/EV, which am experiencing unexpected battery drain. The issue started within a short period of drive and I've noticed that the battery level drops significantly.
I've tried [Diagnosing the control Unit Powertrain PTCU which i got some fault codes
[P0C43f2- the coolant temperature sensor in the Hybrid/EV has a malfunction]
[P0CD6F2- coolant temperature sensor 2 has a malfunction]
[P0AC500- temperature sensor B Hybrid/EV has an electrical fault]
[P0C32F2- the cooling system for Hybrid/EV has a malfunction]
[P0DAB00- the equalization of the cell voltage has a malfunction]
but the issue persists. I'm concerned about the potential impact on the vehicle's performance and overall health.
Has anyone else experienced similar issues with their Mercedes Hybrid/EV? If so, I'd greatly appreciate any advice or guidance on how to resolve this problem.
Hello colleagues,
I have MB W129 instrument cluster US version . I want to change mileage to kilometers and temperature to Celsium. I read the eeprom and upload it.
Is it possible to use the ACDP2 for reading out the flashfile to send to a tuner. (Or maybe someone here can help with a tune file ).My car runs the EDC17C56
Iv only used ACDP2 to backup devices before.
Hi,
I need help. I need to replace the engine controller in an Opel Meriva 2009. Engine code: Z17DTH. I bought the same engine controller as the one in the car (same numbers). I wanted to clone it but when I try to copy the eprom or flash from the old controller to the new one, the content of the eprom or flash does not change in the new controller. It is still the same. I tried to do it with foxflash and pcmflash and still the same. I think that this immo blocks the possibility of copying it to the table. Can someone calculate the pin from this bin file for me, if it is good?
The easiest thing to do would probably be to reset the controller, but I don't know the pin code for this new controller. Can someone help me calculate it from its contents?
I recently purchased an EasyDiag 3.0 device from AliExpress that is supposed to be compatible with X-Diag Pro 3. However, I’m having trouble activating it and finding the correct application to download.
Could anyone guide me on how to properly activate the device and install the right software?
Hi
Unfortunately, the file that was read is not original. A previous workshop tried to repair it, but it didn't work.
How can I get original software for it?
SRS ECU have 3 dtc error code:
B010049 - ECU Internal errors - Internal eletronic failure
B011895 - Configuration mismatch - Incorrect assembly
B012654 - Calibration missing - Missing calibration
0285013985 - 50550297
SRS ECU Label attached!
Thanks
I have an Opel Adam from 2013 that when I try to do a neutral position sensor learn ends in error.
Is there someone here that knows the procedure and can share it.
And when GDS2 tells me the car needs to be in service mode, but not how I enter service mode. Can someone tell me how I set the car in service mode?
Just a simple question, can STAR C3 diagnostics change the mileage on a Smart Roadster? All I can find online is the SAM and instrument cluster needs their eeproms reading and rewriting with something like EPZ 2019
Hey! I havent got my winols computer working yet, suffered from a hardware failure some weeks ago, and im a little slow at fixing it. I have a file from a bmw e39 530d (dde4/edc15c4) and i could use some help just running the file at checksum correction.
hello, i have question , my frend try make cruse xontrol on by elm config program , he do what porgram seys, he write samething and after few % stop , now car no strat , cant start , forscan not recognize car , red diode on dash blinking, , i thing he kill ecu , wanna help , i thing i must write fulkl backup to the ecu ?
im right ?
meaby smwbody have buckup files sod803a 5ws40736d-t 8m51-12a650-and kynd,
BMW F31 - dead, no signs of life in car, nothing works, dash dead hazards not working etc.
FEM cant be read with vvdi 2 on bench, no comms
Eeprom read is here with vvdi prog.
What is the next step, how to adapt used one etc.
Hello everyone, I have a Range rover evoque 2016, The front blower works for a few seconds then it stops, after the diag I found the error B1B72-13 LIN Bus 1 power supply circuit - circuit open, and error B1086-87 Air distribution damper motor, probably because of the LIN bus
the air distribution dont work
symptom:
- The front blower works for a few seconds then it stops
- Air distribution dont work
- Can someone help me with wiring diagram for evoque 2016, VIN SALVA 2BN1GH161193, or any idea how to proceed with LIN bus verification
thanks.
