Hi anyone know How to eject Cd from NBTevo2 on the bench. Tool 32 doesn't works method STEUERN_EJECT or STEUERN_EMERGENCY_EJECT
Any manual option ......
Hello to all! I need to replace a dashboard of a evoque 2018 with an used one. This dashboard has inside a nec 70F3525. Have you some solution to adapt it to car? Or is there a way to read mcu and write dump to used dashboard
PLEASE CHECK THE FILE EDC17C11 OPEL MOVANO I DELETED THIS DTC XDECODER,DAVINCI DELUX BUT IT STILL APPEARS IN ECU THEY DO IT IDENTICALLY. THANK YOU IN ADVANCE
I have a 2012 1.2 Nissan Micra HR12DE with CVT gearbox. This car is the nightmare from hell. The car judders in the lower speed when taking off. While im inclined to order a replacement valve body for the CVT im suspecting something more sinister. Using consult3+ I logged a bunch of information while driving to work out if it the cvt or something else and the strange thing is that every time it judders the abs solenoids on different wheels kick in and worst of all no DTC's. So my thoughts are it could be the wheel sensors even though they show the same speeds but highly unlikely im assuming, further from that im suspecting the ECU is doing something strange.
So far ive replaces
Plugs, coils, MAS, temp sensor, fuel pump, TCM, secondary pressure switch in the CVT with no luck.
My ECU is marked Y4 A56-E37, ive found plenty on line with different markings eg YZ A56-E38, they advertise they are from the same car, can I use one of these others or what do I need to be careful of.
Hi Tryed to IMMO OFF for Audi A4 B6 V6 2.5 TDI, because fuel pump was changed with different code. Tryed with 2 different programs to disable IMMO, but car starts and turns off immediately. No DTC's.. Maybe my sollutions are bad? EDC15VM+
Instal nativ DTS8.16, problem with visible in monaco - system setting - interfaces device sdconnect C4 doip original interface(not visible SN vendor module name), C4 in system windows normal visible in sdtoolkit, does anyone solution for this problem? Attaching photo, thanks for help, Xentry 2018 this same system pc work without problem with sdconnect. Is it possible its file installation is corrupted?
Hi everybody. Im stucked with a problem. Audi a4 b6 V6 2.5 TDI, changed fuel pump with different code. I tryed to remove IMMO with two different programs, and still starts and turns off immediately.. No DTC's .
Maybe someone can check or my sollutions are bad?
Hello all
I have Airbag SDM module from Opel Insygnia first i had fault B101D but now when i cleared eeprom test and erase DTC's I have checksum error B101E:4A
Can somebody help witch this solution?
The wiring harness on the vehicle side that connects to front bumper SRS sensors, the front camera, fog lights and temperature sensor is cut. perhaps 20-30 cm of the wiring harness is completely missing.
I've been trying to find information on where this harness connects to, so i could replace it. The local mercedes dealer says that they cannot find any information from their internal systems about this wire.
I tried buying the Alldata EU version from the forums to see if the info is there but all the wiring diagram stuff links to the original alldata site that i dont have access to.
My question is basically (any of these help):
1) Does anyone know where this harness connects to?
2) Does anyone know what part number this harness is?
3) Does anyone know how could i find out what part this is and where does it connect to without disassembling the whole car?
Hello, does anyone know where is the dcu located in Hyundai i30 2018+? Need for adblue off, because ECU is sim2k-510, unreadable. Help will be appreciated.
Hi, I need Global Tis32 for offline programming an Opel Corsa 2009 ABS unit, I bought VXDIAG VCX SE, a buddy of this forum installed me for this GDS2 and Tech2Win, but both programs don't work with this car. I hope somebody can help me or point me in the right direction.