Hey all,
I know this question is asked many many times,but... I am looking to buy tool for esl,key programming, I work only on mercedes cars. From yours experience what is best tool to go for?
Thanks you in advance!
Hi everyone
Just f*cked up my ecu CRD3P.D1 by mistakenly writing a wrong file from a EDC17CP57-43.
Now I have wakeup error and can't write the ori file back.
Tried boot mode but lost one of the boot points, too fragile...
Do i have any chance to restore the ECU?
Tools I have are xentry, dts monaco with vcx se and foxflash.
Anyone here can help me not for free but am looking for a serious person and can help me buy even original IDSS software and VCI for diagnostic of Isuzu truck 2012-2024.
Posted by: Kim1980 - 03-18-2025, 08:40 AM - Forum: Selling Box
- No Replies
OBDSTAR released a new RH850/V850 adapter full kit for MQB IMMO, Ford BCM, Nissan/Renault HFM, airbag reset, immo data/pincode read (Dashboard, BCM, ELV, etc.).
Hi, here a little contribution to those who will need to extract immo data from eeeprom in Simos11.1 link attached and its FREE
Just some Thx and Rep !!
if you find any bug please report here
Hi all, does anyone have a pinout for the service pins on this cluster, its a 2002 gu patrol, original has a temp gauge issue so just need to copy data over, these have the aircore movement so needles are a pain to get accurate again.
One has 6 pins other has 7, i presume its the 6pin i need to utilise 🤷♂️ worst case i will open and figure it out but if i don't have to would be good
I would like to get into cda programming of 2010-current cars. I have not been around programming of any of them. Besides a micropod 2. What do I need to gain access to actually do the programming. Im running a windows 11 laptop. I have a micropod but I believe it's bricked from a failed firmware update. Can anyone send a aliexpress or Amazon link to a product that will work with windows 11. And what subscriptions do I actually have to pay for.
Price per file - 5euro
"I do not take responsibility for the quality of the files; I assume that while there are perfect ones, there are also complete junk. That's why the price is as it is; you just choose a file and I send it. However, there are quality ones as well, so make sure to check them."
hi
any guru for KEFICO SIM2K-260?
i have a kia with this ecu and i need remap ...
its a complicated work..car have hybrid turbos and fmic,dowpipe ...
if someone are interested i do this work pm me please
of course no free job
thanks
Hello all,
I'm struggling with Vw passat b6 1.9TDI manual EU with EPB(right parking brake motor voltage supply), firstly it was problem with rear right motor, I replaced it to used part but it works on table. Previously motor was bleed with brake fluid.
I checked the wiring to module there was brake fluid in the module plug unbelievable but possible.
After that I checked module organoleptically, then put it in place.
Parking brake switch lamp and parking brake control blinking.
Next step I thought that will be the last one, coding for no. 11, codding accepted, basic setting and there was first interesting thing in parking brake function test: current left motor 0A, count number 0, current right motor 0A, count number 8. I could turn on brakes from switch but only the left one worked. (on one sgo.file right motor shift to 11 and thats all)
I checked number of module it was 3C0907801B I flashed that with files from net... I read it there need to be flashed one by one files xxxxxxxB -> xxxxxxxxBZ -> xxxxxxxxxGX -> xxxxxxxxG I did and there is problem to code for 11 no.
I tried on other files which I have, but the same, can't to code module..
One thing puzzled me, maybe some one put bad files into the net, cuz when I flash module with file xxxxxxxB, on computer ecu information it's xxxxxxG... as if the names were different and the code was different.
Abs module coding is ok.
Maybe someone of u guys have more experience with that problem, and know more. If u can help I will be very grateful.
Hello friends, last time when i use ford fjds looks like i run it for free with licence from forum but it was one year or two ago... ... Now i need adapt new ecu for ford transit 2.2 tdci 2011, looks like now have to pay for licence , yes ? Or still can get licence for free. ?
hello , i need remove the speed limiter edc17c10 citroen jumpy 0281030546.I tested some files but it is still limited, it does not go beyond 150 km/h.attached original flash and eeprom and the files I have already tested.I would appreciate it if anyone could help
thanks
![[Image: 25031717422645619806.jpg]](https://www.obdii365.com/upload/pro/25031717422645619806.jpg)
![[Image: 25031717422030556432.jpg]](https://www.obdii365.com/upload/pro/25031717422030556432.jpg)
