Hi,it is my first post so apologize for the inconvenience.
Im looking someone who retrofit original engine sound sytem in audi a6 2019(c8)
I have connected used modul (4k0907160A)
Add this option in getway now i have connectiom with him (C0 actuator for exterior noise)
but have error inside U10D900 - Incorrect vehicle model
and i dont have option in MMI(drive select)
I have odis online with 6154a head, but I've got some trubles using it.
I dont have svm code so I cant assign it to the vehicle.
I have 4K0907160A.frf but after upload the same fault and no sound...
This will update the system for EESC333, ETHOS EDGE, MODIS EDGE, MODIS ULTRA, SOLUS EDGE, SOLUS EDGE2, VANTAGE ULTRA Imports and domestic to 18.4
First off always back up your stuff!! If you're not sure how ASK!! Rufus is an easy way to make a full backup of your card do not continue till you've made one!!!
You have been warned !! So please do
The how-to:
(as much as I can lots of aggravation and retries so.. I believe I got it right here)
Put the files in the GOLD_SOLUSULTRA folder (as the card was gold). On a Blank card, or your original (always back up your stuff!!) You may need to rename the card with your system's type (use the name snap-on uses, examples are in the 184 folder. I.E. (GOLD_MODISULTRA} also take note of the name it has currently you'll want to rename it after the update. reboot the system (You may also need the files that are within your systems folder? So if it fails. copy those to the root of the card and try again) let it run, and update. Then copy the license.ini from THAT card and put it on a copy of your original card (always back up your stuff!! ) or use your original card.
if using the original card delete all files and folders except the license.ini file you just copied over
Later you can copy back your. user data folder and system bin (previous vehicle or vehicle history or whatever)
also copy the folders from 184 \SU and 184 \base to the root of the card; now reboot.
Basically your copying the update files and the newly generated license that
was made by the "gold card". this will run the actual update with your new license but with the original card and recreate the new file system plus sync up all the licenses,
Thats it.. If you made your backups your all good if it fails!!
if not just use the backup to restore..
Depending on the version you have now you may need to download and run the next new update one at a time in the same way..
There is a little trial and error for this I had little to go on So I tried a lot and this is what I came up with.
You can thank me after your system is updated
P.S. You don't need all the files in the torrent just the ones mentioned . The rest are my working copy (my backup per say )
Hello!
I have some truble with this car. I supose that in software are some dtc off. Is it posible to check if there is dtc off? Or have someone an ori file for this car?
Could someone drop link of a complete installation files for CAT SIS 2021, so everyone could find it easily. I've seen many threads posting installation files, but a lot of them are not complete and some files are missing.
I have done hardware part retrofit of the RSE, the monitors light up and work fine. What coding should I be doing. I have Esys and ISTA, is it enough just to add 6FH to VO and code all the modules?
I've been trying to code a new key & think I must be doing something wrong as I can't seem to generate a dealer key or get my blank key synced with the immobiliser.
In a nutshell I allowed a former gf to use my vehicle & just to add some extra fun to the break up she decided to toss my only original key in the bin.
Thankfully I've managed to get it towed home but have been unable to drive it as I'm lost as to how to complete this procedure given I have the equipment capable of doing it.
Hi friends im trying to swap and reprogram ecm on 2005 nissan tiida. My autel asks for 5number code located on bcm , either the 4 number pin code. I removed ecm but i cant find 5 number code that im supposed to enter can anyone help me out?
UPDATE: if you are first timer like me and have no idea, this might help , some of old nissans have immo off. in my case it was immo off and the donor ecm was with immo thats why car didn't start, and when i tried to read immo encrypted 5 number pass or 4 digit pin. my autel would either throw N/A or FFFFF , meaning this car had no immo. learnt it hard way , dont waste time on looking for bcm and immo to read encrypted password from the sticker it might not even have, just rewrite or solder eeprom from old ecm to new one( simplest solution...)
P.S In my case cylinder 4 ignition coil had no impulse (dark green wire as i remember, not sure) now wiring issue. apparently bad spark plugs blow you coil pack which then shorts circuit or ignition driver chip... some people can just fix it or swap out that chip if they got proper equipment, if not just swapping ecm...
P.S 2 i have been so unlucky to spend this much time just to figure out password for immo then to rewrite eeprom in new ecu just to realize that this ecm has same burnt ignition driver chip(even worse cyl 3 and cyl 4)...
here is the image of the ecm immo eeprom is st95230 and ignition driver is NEC something...
Anyways good luck hope this helps you to not waste more time
Hello, has anyone had a problem with the Mitsubishi Fuso engine ECU EDC7DC4
Cannot erase error for egr p0401
I read that the eeprom needs to be modified.
Has anyone had a similar problem and has a solution for this?
what tool would be best to transfer IMMO/CP data from the current analogue cluster to a new VC one?
Car: Seat Ateca model year 2018.
Part number of current cluster in use: 5F0920751E
Target cluster to swap the current one with: 5F0920790A
According to my research these clusters are NEC35XX (encrypted)/IMMO 5a.
I saw that tools like Poldiag could do it but I'm not a professional, only want to do my personal cluster swap and therefore it is way too expensive.
Furthermore I saw that Carprog seems to be capable of doing the job as well with adapter 14 PLUS there is a chinese clone version available for roughly 60€ at aliexpress.
- However, it seems the version on aliexpress is 13.77 and the screenshot from Carprog shows 14.43. Problematic?
- No idea if this kind of stuff requires online connection to work as well or if it could be done offline.
A new VC cluster with the part number mentioned initially is quoted with 850€ at my local dealer, I could easily adapt it with ODIS online without all the hassle. A used cluster is roughly 400-500€ so if there is any kind of solution it should cost less than 300€, otherwise such a solution would make little sense.
I do not know anybody here in Austria who could do this kind of stuff and is in possession of the right tools as well.
Are there any other solutions you could possibly think of for allowing to make this upgrade in a financially meaningful way?
Any help or ideas would be much appreciated.
By the way, not afraid of the soldering job on the dashes etc. or other technical stuff that might be required. I have expertise in the field.
