Heya all,
my 2014 Mercedes W212 E250 has an issue with the MAF
P010129 Mass air flow sensor 1 has a malfunction. There is an invalid signal.
Bought a new MAF, fitted, taught in via Xentry, reset codes & test - Still has P010129
Found two wires had rubbed the insulation off by stupid plastic Eng cover, reinsulate & retest - same fault
Wondering if the faulty wiring has damaged the Eng ECU?
Is a MAF delete possible? - Car drives, not very nice up to 85km/hr then not so bad. Have to manually select 6th once above 95km/hr
Fault is while engine is not running as well as running - so I doubt it's caused by an air leak
Hi friend
I have problem with Volvo 2015 v40 d4 ECU eprom
Car wont start after rewrite eprom
Eprom dont allow writing on some adddres,only write 3f
Write ori and then read out,and not same when compare
Anny solution?
Hi friend
I have problem with Volvo 2015 v40 d4 ECU eprom
Car wont start after rewrite eprom
Eprom dont allow writing on some adddres,only write 3f
Write ori and then read out,and not same when compare
Anny solution?
Hello friends. I am getting an error code on my Peugeot vehicle. The explanation of this code is incorrect injector coding or incorrect signal. I coded it with Diagbox, Launch and Bosch KTS device but the error did not fix it. When I first start the vehicle, a warning comes up and when I turn the ignition off and on, it fixes it. Does anyone know a solution to this?
I'm having trouble programming my 2019 Mercedes-Benz W213 300D using DTS Monaco version 8.16. Specifically, I'm trying to variant code my HU55 head unit, but I'm encountering some errors.
The error messages I'm getting are:
STAT: Cannot resolve interface from configuration.
DYN: Error Code Unknown error code (0x80004005).
An internal error occurred in the MVCI diagnostic server.
My setup includes DTS Monaco 8.16 software and an OpenPort device. I also own a 2018 W213 E200, and using the same setup with the OpenPort device, everything works without any issues. This suggests that the problem might be specific to the 2019 300D or its configuration.
I've ensured all necessary drivers and software updates are installed, verified that the hardware is properly connected and configured, and attempted to restart the software and hardware.
If anyone has experienced similar issues or knows how to resolve these errors, I would greatly appreciate your assistance. Please share any relevant advice or solutions you might have.
Hello everyone!
I have a controller with numbers in my Ford: 7G91-12A650-AAC 5WS40761C-T 7GAC J38AC After using the interface and reading the driver, I have this information HW: B4YQ5E6AFRB8300
SW: 10132165AA
VIN nr.: WF0SXXGBWS8K70650
SW ver.: 7G91-12K532-UC
Spare: 7G91-12A650-AAC
Engine:
HW Ver.: 6G91-12B684-BA
SW upg.: Installation:
My Questions for Professional People
1 Is everything original here?
2. What ECU numbers can I use as a replacement part?
i have opel vivaro b 1.6 92 biturbo with not staring problem. Tank pump ok, HP pump and injectors tested, pressure sensor and fuel metering valve on HP pump good, also wiring tested. Tried cranking with injectors taken out of engine- they work and opening fuel flow. With injectors in engine, car ir cranking but not starting. After cranking for 5 or more second, i get error P0005 fault. after throwed fault, fuel cut off to injectors. Pressure in rail reaches 2000bar which i think is max pressure for it. Could be eeprom corrupted?
Already checked timing, compression, camshaft-crankshaft synchronised when cranking, there is no ecm fuel disable, no crash.
Hi,
i need help with water in fuel dtc off, clip code is DF196 another tool gives me P1264 and from info i found it should be 188C code in flash file,
i tried to tamper with 188c code but without full success,
I have an instrument panel from a Renault Twingo 3 and it can no longer be reached via OBD, probably due to adjusting the odometer.
Does anyone know where the software is located and how I can repair it?
Hello 👋
I need virgin film for toyota ecm 89661-fa090 .
I replaced only used ecm and have all keys
Need virgin file to coding used ecm
Toyota hilux 2023
I have a Renault Kangoo K9k engine
in another workshop they changed the engine ecu DCM 1.2 for some reason,
then the steering does not work.
with the clip I can not change the congiguration
Does anyone know how I can fix this problem or had some issue and how solved?
