Hi, I replaced a light sensor with the light and rain sensor on a 13 Mercedes W176. I don't know how to calibrate this unit. I have xentry and Vediamo. After replacing I get a code: B22E34A The rain and light sensor has a malfunction. The wrong part is installed. B225F54 The light sensor has a malfunction. The calibration is missing.
hello guys, i have here a 2018 audi q7 with defective airbag module 4M0959655E, water damaged.. owner got a used module from a donor car with the same number..
i tried read old module eeprom and write to the donor eeprom and got checksum error..
i tried to read mcu D70F3508G with vvdi prog, tried all possible connections but no success
im sure this subject has been beat to death with this dme, but im gonna try anyways. Can anyone point me in the direction of what hex address has to be edited within the 29f200 chip to be rid of this demon. i was given this car and it was in shambles, somebody tried to steal it from a buddy of mine about 4 years ago, destroyed the interior trying to get to various wiring to attemp to hotwire this car and failed miserably. it has since sat on his property in the back 40 mostly ignored until last year when i got ahold of it. i've got the full read from both the dme and the 29f200 flash. if theres anyone out there that could help me get this thing finally running i would be forever greatful.
Hello,
Following a starter kit change,
I would like to update the VINs.
All the ECUs have been modified except the engine ECU.
I changed the VIN in the EEPROM (it appears 6 times) by calculating the checksum with Renault Tool.
But the old VIN always comes back.
I heard that the flash drive needs to be modified, but the VIN isn't present in it.
How can I do this?
Thanks in advance.
Sincerely,
Hi to everyone... i post this tread to ask help to do DPF OFF+ ADblue OFF .... Please only manual tested solution that works with DCU unplugged ... on Fiat 500x equipped with Marelli 9DF HW001.. i already tired other software and manual solution with DCU plugged but without success... i hope to find the right soution .... Rauch15 Thanks in advance ....
Can somebody help with these ET76-14B321-CG SRS from ford ?[url=https://cartechnology.co.uk/showthread.php?tid=103716][/url]
XC2336-72 dataflash3 attached:
Thanks!
i need help, i have a Nissan 370z. The customer modified the exhaust, catalytic converter, and pistons.
Now, with the stock software, the car has 311 ps instead of 344 ps, and even with tuning,
I only get about 340 ps.
If someone has done an original Dyno run and could send it to me, I would be happy
Deutz DeCOM is a diagnostic tool interface, often used with SerDia software, for diagnosing and programming Deutz controllers, particularly those in trucks and other machinery
It allows technicians to access and interact with the electronic control modules (ECMs) of Deutz engines and machinery
Serdia 4.0 with level 6
license lifetime by USB Dongle
** Database Extra
** Database Extra
** Database Extra
OR COMPLETE PACKAGE C - 1500 EURO'S
PAYPAL PAYMENT ACCEPTED LINKS VIA MEGA ACCOUNT PM FOR MORE INFO AND XLS LIST
TESTED SOLUTIONS
500 EURO'S EASTER SPECIAL FOR EVERYTHING PACKAGE A, B AND C
Hello,
I have a 2000 Mazda B2500 with a Mitsubishi immo box
UJ13675G2C
9002280421
and need the PIN code.
The car doesn't have an ECU to read the EPROM—at least I can't find one.
The box and the immo part are on the solenoid valve on the pump. Does anyone have a way to get the PIN with the
serial number?
Thanks in advance
![[Image: 25031317419312818999.jpg]](https://www.eobdtool.co.uk/upload/pro/25031317419312818999.jpg)
![[Image: 1-3.jpg]](https://www.autoepccatalog.com/wp-content/uploads/2023/11/1-3.jpg)
![[Image: Deutz-Serdia-4.0.jpg]](https://www.autoepccatalog.com/wp-content/uploads/2025/03/Deutz-Serdia-4.0.jpg)
