Dear members, I have a 2007 Maserati Quattroporte with faulty BCM, I got a used one and I wrote the eeprom and flash from original MCU MC9S12DG256B but I still have an immobilizer fault and the Transponder code is wrong, any suggestion please or is there a separate eeprom to write apart from MCU?
Hi, can you help me with mileage change on hyundai i30
old mileage 194283km i need 188233km
can you chek if dump is ok? becouse i have some doubts, read by Xhore Pad MICROCHIP 93c56c
THANK YOU!
I have been a long time user of Diagzone , Prodiag, and other Launch-based software. I recently was using Thinkdiag2 with Diagzone. but after upgrading to a newer phone that does not support older 32bit apk files like all launch based software, I decided to give the original Thinkdiag2 software a try and flashed back. I have found it to work very well and i like it enough to continue to have it on my main device.
My question is if anyone has a discount or cheaper way of getting their $499 USD Lifetime VIP subscription? Any suggestion would be helpful. A lifetime subscription seems very good but their price is a bit high.
Hello, I need some advice. I wanted to deactivate the tyre pressure message on my 2009/10 Skoda Roomster. But VCDS doesn't show me a way to deactivate it? I looked on YouTube and did the same thing, but it didn't work for me. Does anyone know how I can still do this? Thank you.
by w167 under pasanger seat is somes unit and inside this unit somes guy crack chip , after is impossible look position car . someone know witch chip need to crack ???
is about sale new car to other country .... delaer restrictions ....
Hello guys, i want to exchange experience with the new Ista Native ilean offline 4.52.21 version . Before someone to comment the installation is made professional and for sure not have mistakes! / checked 832 times/ First i was start with my tried to update my experimental (CLONE) Icom next 153v firmware , in automatic mode the update was successfully to 154v !!! I read the car, but after i take off icom from obd2 , and try to read new car, itool and ista dont see the ICOM ! after that i was make attempts with usb stick to back to live the icom , after attempt itool see again icom with firmware version 154, after i downgraded the version to 153 and icom was revived and worked with older ista. Second TEST OEM ICOM NEXT working normally update and all was ok.
Third step i was tried to test kdcan cable maybe it was my fault because dont use in my work kdcan cable or setthings was not good but kdcan cable cannot read the car, after that i was read kdcan no more work on newest ista....
In Last step i was tried to test Enet Lan cable.....was read f01 and g15...and pain starting i am sure it was 100 % properly set up for enet works but Ista read the cars almost 20 minutes !!! With Esys Ultra no problems with enet read the car for a seconds....with enet was terrible slowly reading never like before that !
I will be helpful if someone who is testing 4.52.21 shared his experience or someone if know something more about newest Ista For sure for now i can said chinese icom next clones finished to work till version of firmware 153.
Hello everyone, has anyone had the alternator not charging on the 8f3 control unit mounted on a 1.3 MJT? I was told that the problem can be solved in the control unit but I wasn't told exactly how.
Hi I need assistance in identifying a device I have. Pictures attached.
I thought it was VXdiag which VXdiag manager identifies as OEM-VCI serial number M83MB39070.
How will I connect it to Xdos 23.9.
Any advice will be highly appreciated.
Flash via OBD with Bflash/CMD.
Other tools need bench, and make sure your tool does the checksum.
If the price is out of your budget, please do not contact me. If you contact me please send a link with your calibration so i can respond if we have a solution.
Hello, i replaced faulty sgm/sim module, flashed vin with winkpf, but i cant find sgm module in ncsexpert, only see sim maybe its the same? I have Time fault in inpa , į tried reseting with tool32 but no luck. I assume without programming it correctly in ncsexpert i wont be able to reset Time? Can anyone help please
Hi Can anyone help me to remove the egr on this ford please
FORD MONDEO 2.0 TDCI DELPHI DCM 3.5
WF0EXXGBBEAT79044
UPG.SW: BG91-14C204-FJ
0072LA00910188
HW NO:AG91-12A650-AG
ECU NOS-BG91-12A650-NE
thank you very much
Good afternoon, friends of mhh. Today I need help installing a donor airbag ECU. The ECU I had installed is no longer the original and had these DTCs:
b200000
b100b1b
b100511
b102029
I've tested the donor ECU and it's giving me VIN mismatch errors and the same DTCs, but without the B2000. If I enter the information for 95320, the same codes for mine, including the B2000.
I'm leaving the original dump that came with the car, VIN correct, here in case anyone can help me with this task.
The unit reference is 6R0959655M hw10
Thanks in advance.
Hello
Can you help me with change radio in corsa D
I dont have pass code from car,
I was read old cd30 mp3 dump in attachment
and new cd30 damp in attachment
Do i need read display to have pin?
Can you make radio virgin for me?
Thanks for help
S-BG91-12A650-NE
