Hi guys.
I'm desperately looking for the ESP control module. It's not integrated into the ABS because I disconnect the ABS and keep connecting it to the ESP.
The car is a 2007 or 2008 Ford C-Max.
I have a processor error in the PCM and CAN communication errors in the ABS and ESP.
The car starts and stops after about 20 seconds. It also won't accelerate.
Thanks.
I using B class W246 2013 year by mistake i just RESETING the learned valueas of my car . Now i dont have Stop emergency break distance also i have all the time icon for my desk " OFF " ass attached file
. I did order for the obd cable J2535 then can someona help me with it ? I have to install Vediaomo ? Many thanks for help
[font="MHH Font", Calibri, sans-serif]Hello, can someone clear the ABS pump DTC from the engine ECU? The DTC is C1300. The pump is working fine, but it creates this DTC in the engine and the fault light comes on on the instrument panel. Can someone clear this DTC?[/font]
Hey guys. I have the latest Honda HDS / I-HDS software, direct from Honda's servers. I also have the latest ECU Rewrite software, again, direct from Honda's servers. Honda I-HDS replaces HDS. To diagnose newer cars, I-HDS is required. The interface is easier to use. So you need to install HDS first and I-HDS afterwards. HDS will NOT run by itself. HDS cannot access IMMO anymore. You would need i-HDS installed. However, you will need to be a registered locksmith and have credentials for Honda INsite. None of this is provided, therefore will not work. You can purchase key programming device if you want to do IMMO. Hondas HDS v3.105.036 Honda i-HDS 1.010.019 J2534 Rewrite 1.00.0034 This doesn't expire. It's fully activated. This will only work on Windows 10. Anything older than Windows 10 is not supported. HDS will work for any region. (USA/Europe/Asia/other markets) The Rewrite software is meant for the North American market. The Rewrite software allows you to update powertrain modules such as PCM and TCM. You can use other J2534 devices, as I use my Snap On Pass Thru Pro 3. Some examples of tools that you can use are CarDaq-Plus, CarDaq-M, GM MDI and much more!
The payment will be made via PayPal. Please PM me for more information. **** Please note, I do not have a Honda SPX MVCI tool, so I can't test out if the CM Updates will go to the memory card. I'm not going to guarantee that I can make that work, without having the scan tool in my hand for me to test out. I can't guarantee that the SPX MVCI or Denso DST-i will work with this software. If you want to use the ECU Rewrite feature, you'll need to have valid Honda credentials to be able to do so. That is not provided nor is it included ****
the car was manufactured in 2016, this year radar 561907561a and 561907561b were installed, how can I understand which radar I need? VIN code 1vwbt7a37gc066150
Hello friends. Need help in MERCEDES ML EDC17C57 SCR OFF. Namely. I made a mod, there are no errors, the urea tank that did not work shows a full charge, but I can not find the switch of the start blocking timer after standing. I attach the stock files and my mod. Thanks in advance. Please do not send advertising of online servicesThe solutions Davinchi and swiftec don't work so please don't upload them The solutions Davinchi and swiftec don't work so please don't upload them
Hy all, I have replaced the control unit for the fuel pump in my F31 3.18D. My control unit was defective. Do I have to re-learn or code the new one? and if so, can I do this with ista etc? thanks
I would like you to help me.
I installed the V165 version, but I can't connect the VCM interface at all. OEM Ford VCM.
I tried both x86 and x64 versions.
It doesn't see any vci manager. SDD recovery tool not see interface.
The Interface works perfectly on another system on Ford V106.
Maybe only VCM 1 works on another version? I wonder what the last version that works on JLR SDD could be?
Thank you everyone for your help.
Hello, can someone clear the ABS pump DTC from the engine ECU? The DTC is C1300. The pump is working fine, but it creates this DTC in the engine and the fault light comes on on the instrument panel. Can someone clear this DTC?
Hi. I have Suzuki SX4 1.6 petrol M16A engine with ecu ME17.9.51 and i need dtc off for test. DTC: P0303 P0300 File in attachment, thank you for your help.
I try to made tune for offroad car with m57 engine and edc15c4 ecu. I would be grateful if someone more experienced would look at the end result, and if they have any constructive ideas, I would be happy to receive them.
I am currently looking into getting another diagnostic system.
I have a launch system but just want to have another one too just so I don't get caught if anything happens. I am looking for one that would be complement the launch system.
I am currently looking at the otofix d1 pro and the topdon phoenix lite 2 or 3. I just want to know if anyone has both of these and which they find better or if anyone has any other suggestions around the same price range as either of those.
Hi guys
If this is not right place please remove...
Anyone of you have some photos where the eeprom is located and can share i will very gateful ...
Volvo V40 my2014 i have U3000 fault
Thank in advance
Hello. I have the ISTA D / P installed by a professional but I'm keep getting the ISTA not released error. Does anyone know how to fix this? This has been ongoing issue.
Hello everyone. I'm new here and in this type of work I'm doing, this is my first post and I apologize if I'm posting in the wrong place or if this question has already been asked. I need to learn the key of a 2001 Smart 450. I have Xentry and DAS but only via Openport and I use Tactrix. I can only access the engine module. Whenever I try to access other modules I get the error (DAS fault1.2-2.518). I suspect it has something to do with Tactrix not reading K-lines. Could that be it? Does anyone have any tips that could help me? Thanks everyone!
![[Image: sEdg1380Hq.png]](https://i.imghippo.com/files/sEdg1380Hq.png)
