Does anyone do an online ECU update for a Peugeot 508 2019 DCM 7.1a? I need to reflash the software on my computer. It was installed with a third party and I need to update the chassis. I have a Lexia clone interface.
Hello everyone, I have a question about globaltis v32 offline. I need to reprogram all the control units (ecu engine body and other ) of an opel corsa d 2008 Z12xep. As j2534 I have a mongoose pro jlr China version that I needed and worked very well in past for programming in jdd, and also for use with odis. I have installed globaltis v32 on vmware and it is recognized correctly. In your opinion, being a j2534, can it do sps programming of the control units?
Hi, is anybody able to pull the 6 byte code from this RFHub? Car caught on fire, rebuilt everything, and now have code U0168 on PCM (no communication with security module), and a code in the RFHub saying it did not receive a handshake from the PCM.
Unsure if that's a secret code issue or if it's one of the two modules that is bad.
Hi, I have Toyota Techstream v18.00.008 installed in my laptop. The subscription is active and I am using Mini VCI J2534 with "MVCI Autokent X64 1.4.8" selected in the VIM Select inside Techstream. Everything was working fine. Techstream would detect my car instantly when connected thru the OBD2 port.
Suddenly, it stopped working. I have attached the error message it gives which says "Selected system is not responding or not available. Please check the repair manual for applicable system".
Appreciate how to fix and what's causing this issue.
hi i have a problem with rear lights in A169 mercedes i arranje a used front same
same part nr A1695453032 but car doesnt crank and i lost comms with engine ecu and abs with used one no dtc on used sam does anyone knows if i need to code this kind of sam? thanks
Does anyone know of a solution to block a u1510 code on a 2018 Sierra 1500?
Chasing down a u1510 code for the theft deterrent module/ultrasonic intrusion sensor and can’t figure out the issue. Worst case I’d like to block the code if possible so I can have remote start(disabled by engine light)
N129/1 - Power electronics (SG-EM) do not have communication with IC, combustion engine, High-voltage battery, ignition lock, transmission, esp
but when I am pressing test on any of fault code it shows that modules communicating.
Also, many other control modules shows that there is no communication with combustion engine, but once again when doing test it shows that there is communication.
In engine control module there are faults:
Communication with control unit "Electric machine B" has a malfunction. The message is missing.
Communication with control unit "DC/DC converter" has a malfunction. The message is missing.
Is it problem in N129/1 - Power electronics (SG-EM) ? Can it be ground problems? If yes where I can find ground spots for power electronics?
If this module is faulty I guess it is not enough just replace it with other used one as it is THEFT-RELEVANT PART?
Hi there i got an skoda fabia 1.2 petrol dq200 0AM927769E the car sometimes cold couldnt drive in reverse and when warm it couldnt pass 6th gear and throws the fault below i tried basic setting it fails at 0-0-255-85 i checked the forks manually all working as it should no play nothing tried replacing oil in manual gearbox but no luck valve body pressure is absolutely fine anyone had this issue before?
Hello mhh
please need immo off in flash and eeprom for fiat strada 1.3 2012 ecu MJD6F3.S1
I tested the off on flash, the car started just once
thankx in advance
Can someone check these dumps for me, Battery was not charging, So i read with vvdi prog, did repair, charge battery to 13v and then reinstall board and still faults with no charging
U141100 Battery terminal recognition open circuit
P1B0200 12v battery monitoring no function.
I have attached original dumps both d and c flash and then the read after installing battery. I noticed there are 2 versions with pinouts on vvdiprog I used the first one without removing crystal and read fine so assume that was ok.
Can i have immo data please?
ecu pcr2.1 car no start after flash ecu by Launch online functions , the flash finished corectly but i suspect immo off on ecu.
also have dump config data from instrument cluster.
Hi,
I got here a W213 E Class MY2017 with "Please fill up AdBlue,..No Start in ....+/- 50km"
Filled to 12Liters (of max 15liters) - still warning message on dash
Xentry ShortTest - no fault codes in MRD1 and SCR Module.
Reset Warning message in dash with Xentry - still warning message
Start DTS Monaco done hard reset on IC,ECU,SCR - still warning message.
Close and locked the car and wait for 30seconds. Unlock car and opened the door --> still warning message.
There are no fault codes at all and when I read fill level value it showed correct level
Any idea how I can reset this correctly with dts monaco ?
