Hi guys, i have C5 Aircross from 2020 - With DCM 7.1a I read flash and eeprom BOOT MODE by Fox , then send file to SCR OFF, but after write i had errors oil Pressure P0520 and P0195, i found thread, the checksum need to be corrected ? Or other solutions ? I saw that someone solved by doing the checksum with DS MANAGER
Hello everyone, i need a ECU wiring diagram for BMW E46 320D 110KW 2002. I need to know which two pins are connected to the alternator and which wire goes to the 1st and 2nd pin on the connector. I currently don’t have access to Autodata Online so i have no other option but to ask for help. Thank you.
Hi we have a 2019 Citroen C4 picasso with fault (Code B183f number of engine starts and or restart counter fault), unable to clear no engine faults either. Tried BSI reset and fitted new battery and coded in.
Unable to reset stop start counter in BSI due to not able to unlock it first using launch x431.
Anyone have any ideas car drives fine
hello , can samebody help me with procedure what i must do for remote diagnostic or codding bmw ? for example i must connect with cliwnt bmw f30 , hew have enet cable, any desk and enet remote sesion helper program , he connect enet to the car , open anydesk and give me acces , i open program enet remote ...... helper i see ip mac and vin number , , all program like esys bimmer untility or ista is on my laptop , what i must do for connect my laptop with his bmw ? thx for eny help
Hi,
An open implementation of NAG52 (722.6 Transmission controller), complete with KWP2000 diagnostics and CANBUS support, with support for all cars that came with the EGS51, EGS52 or EGS53 TCU.
Finally i can read my friends T5 CAAC. This is tuned by a hungarian guy. It has stg1 and EGR off. The car cant regen after this remap...
I would like to know its a bad tune or something else happen with the car /i think bad tune/...
Somebody could check me this file?
Fast and high-quality remote software installation
2–3 weeks for software testing
Individual approach
System of bonuses and discounts
We can also offer a solution for all cars, trucks and agricultural machinery.
Bendix ACom PRO v1 Diagnostics Engineering (2024) - 165$
Description:
Bendix ACom PRO - THE ABILITY TO CONFIGURE AND TROUBLESHOOT BENDIX COMPONENTS. Device - RP-1210C, Noregon DLA+ 2.0, NEXIQ USB LINK 1, NEXIQ USB LINK 2, DG TECHNOLOGIES DPA5
If you have reached this line, it means you have questions - we will be happy to answer them!
Hello to everyone!
I will keep it as short as possible and I hope someone can help me asap with this problem I have.
A few months ago, my Radar Module, as known as SGR or RDU has torn apart, literally, every layer and pin bringing it to it’s final days.
Now I bought a new Module, exact same one, but with other part number as it comes from a W212 and I need it on my W221
Xentry won’t communicate and I went with another OBD scanner (ThinkDiag) and it communicates fine
Then I went with Vediamo and I have to choose the cbf file from DAS as RDU_212 and not RDU221, because of no communication
I don’t know how to go further, so I ask for your help, as my knowledge in Vediamo is a little bit restrained as I do not know so much.
Is it possible to make it work on W221? Because it is basically the same system
I don’t got Online Coding, I only got offline and the old data cannot be retrieved because the old Radar Module is dead
FIAT DOBLO 1.6JTD 2017 BOOST CORRELATION ERROR AFTER 30 MILES,I HAVE REPLACED BOOST SENSOR WITH A PATTERN ONE GENUINE NOT AVAILABLE, IN LIVE DATA SENSOR IS STUCK ON 1135MB UNPLUG IT AND SHOWS 3000MB.
USE A SENSOR SIMULATOR AND IT RUNS THROUGH THE RANGE AS IT SHOULD 0-3020MB
SO I HAVE ANOTHER DOBLO HERE SWAPPED THE MAP SENSORS AND THE PATTERN SENSOR READS AS IT SHOULD ON THE OTHER CAR FOR TESTING.
THE GENUINE SENSOR STILL READS 1135MB ON THE FAULTY CAR
I CUT THE SENSOR WIRE FROM THE ECU AND WIRED DIRECTLY TO THE SENSOR NO CHANGE SO THE LOOM IT GOOD
Hello everyone, need full dump backup for a peugeot expert 1.6 hdi 90 hp 9HU engine code no DPF.
The original ecu has been replaced by another one from a peugeot 307 engie code 9HX however the engine cuts at 2500 rpm, so i htink that maybe the software was wrong and i dont have original ecu to find SW and HW original.
Help please,
Fabio Santos
![[Image: 72.png]](https://fonts.gstatic.com/s/e/notoemoji/16.0/1f979/72.png)
