Hello everyone I have an Opel Mokka from 2016 which the instrument panel does not work and gives airbag failures, TPMS, immobilizer etc, none of the needles work, in airbag I have the DTC U0155 also in BCM and in air conditioning, I have looked for a second hand and cloned BCM but the problem continues, I have passed a direct cable from the frame to the LIN communication radio but it is still the same, can anyone help me?
Hello! I have an A6 C7.5 2.0 TDI 110 kw CSUD S-Tronic (0CK DL382), and I’m experiencing an issue with very delayed shifting on uphill drives.
Example: I’m driving at 77 km/h, going uphill, in S mode, gear 4, at 2900 RPM, and it doesn’t shift to the next gear (5), even if I release the gas pedal or press the brake pedal. It only shifts at 3200-3500 RPM in S mode or at 2000 RPM in Comfort mode.
This problem appeared immediately after I performed a Basic Settings reset in the Engine module: [IDE03373] Resetting learned values of cylinder pressure sensors.
I suspect the issue is caused by the ECU learning new values from cylinder pressure sensor 3. I’m fairly certain there’s a special driving procedure required for the ECU to learn these new values. I’ve tried driving normally, but the delayed shifting in S mode persists.
Additional Information:
The gearbox oil was recently changed.
Basic settings for the transmission were performed with ODIS.
Both the ECU and TCU software were updated.
However, none of these solved the issue. Maybe a SVM work?
To reiterate, the problem started immediately after performing [IDE03373] Resetting learned values of cylinder pressure sensors in the Engine module. No DTCs are stored, and I don’t have an option for adapting the new values with ODIS or VCDS.
Since then, I’ve performed multiple tests. I’ve reset [IDE03373] several times and tried different driving procedures—initially driving gently and then more aggressively. Each time, the shift points changed.
On one occasion, I even managed to fix the problem: the car no longer shifted at 2900 RPM in S mode on an uphill; instead, it shifted normally at around 2200-2300 RPM under light load. However, in Comfort and Auto modes, it started driving at very low RPM, which didn’t feel right.
Because of this, I reset [IDE03373] again, and now the delayed shifting in S mode has returned.
Is there any official driving procedure to follow after this reset?
Hello fellow members I need some help with emissions delete file it is from a 2021 ford 6.7 P.S. I purchased a file from ziptuning actually been using them for my ford trucks I've done about 4-6 trucks with them. Come to find out none of their files work, just that my customers didn't tell me. Files have no DTC's but after driving you get emission warnings and random regens that wont idle down this last one all of a sudden got dead pedal no codes. all were retuned with hp tuners after no problems all sen. dis. Ziptuning stated some sensors need to remain connected. These trucks were read & written using pcm flash with SM2 Pro. which is cheaper than HP.. I don't know if files only have dtc's not reporting or just bad tuning!! ANYONE HAVE SOLUTION WILL PAY FOR GD FILE. Also anyone have DAMOS OR SUPERMAPPACK for these ecm's MD1CS006... Would appreciate input or help!! This is the modded file
So the car suddenly shows a lot of faults on the instrument cluster, and when fault appear the car won't start.
Suddenly the faults can go away, and the car will start. Faults can come back on while car is running.
The following systems is abnormal:
EBCM (Electronic Brake Control Module) 1 problem exist
1.U0104 Lost Communication with Cruise Control Module
BCM (Body Control Module) 8 problems exist
1.B305A No Response From Steering Column Lock Received
2.U0078 Control Module Communication Low Speed CAN Bus Off
3.U0151 Lost Communication with Inflatable Restraint Sensing
and Diagnostic Module
4.U0155 Lost Communication with Instrument Cluster
5.U0164 Lost Communication with HVAC Control Module
6.U0168 Lost Communication with Keyless Entry Control Module
7.U0230 Lost Communication with Liftgate Control Module
8.U0236 Lost Communication with Steering Column Lock Module
SRS (Inflatable Restraint Sensing And Diagnostic Module) 4 problems exist
1.U0140 Lost Communication with Body Control Module
2.U0186 Lost Communication with Speaker Amplifier Module
3.U0155 Lost Communication with Instrument Cluster
4.U0184 Lost Communication with Radio
IC (Instrument Cluster) 5 problems exist
1.U0140 Lost Communication with Body Control Module
2.U0151 Lost Communication with Inflatable Restraint Sensing
and Diagnostic Module
3.U0159 Lost Communication with Parking Assist Control Module
4.U026A Lost Communication with Vehicle Direction Camera
Control Module
5.U0232 Lost Communication with Side Object Detection Control
Module - Left
RC (Radio Controls) 4 problems exist
1.U0078 Control Module Communication Low Speed CAN Bus Off
2.U0140 Lost Communication with Body Control Module
3.U0155 Lost Communication with Instrument Cluster
4.U0151 Lost Communication with Inflatable Restraint Sensing
and Diagnostic Module
HC (HVAC Controls) 4 problems exist
1.B1325 Control Module Power Circuit Low Voltage
2.U0078 Control Module Communication Low Speed CAN Bus Off
3.U0140 Lost Communication with Body Control Module
4.U0155 Lost Communication with Instrument Cluster
TICM (Trailer Interface Control Module) 3 problems exist
1.U0073 CAN Bus Communication
2.U0140 Lost Communication with Body Control Module
3.U0155 Lost Communication with Instrument Cluster
RADIO (Radio) 8 problems exist
1.B101D Electronic Control Unit Hardware Internal Communication
Malfunction
2.B125E Digital Audio Broadcast Antenna Circuit Open
3.U0020 Low Speed CAN Bus
4.U0029 MOST Bus Performance Bus Signal Erratic
5.U0078 Control Module Communication Low Speed CAN Bus Off
6.U0140 Lost Communication with Body Control Module
7.U0155 Lost Communication with Instrument Cluster
8.U0164 Lost Communication with HVAC Control Module
Amplifier 1 problem exist
1.U0073 Control Module Communication Bus A Off
ICT (Infotainment Control Touchpad) 1 problem exist
1.U0078 Control Module Communication Low Speed CAN Bus Off
HVAC (Heating Ventilation Air-conditioning And Cooling) 6 problems exist
1.U0078 Control Module Communication Low Speed CAN Bus Off
2.U0140 Lost Communication with Body Control Module
3.U0151 Lost Communication with Inflatable Restraint Sensing
and Diagnostic Module
4.U0155 Lost Communication with Instrument Cluster
5.U0184 Lost Communication with Radio
6.U0208 Lost Communication with Rear Heated Seat
LCM (Liftgate Control Module) 2 problems exist
1.U0140 Lost Communication with Body Control Module
2.U0155 Lost Communication with Instrument Cluster
FSHVC (Front Seat Heating/Venting/Cooling) 5 problems exist
1.U0073 Control Module Communication Bus A Off
2.U0020 Low Speed CAN Bus
3.U0140 Lost Communication with Body Control Module
4.U0155 Lost Communication with Instrument Cluster
5.U0164 Lost Communication with HVAC Control Module
KECM (Keyless Entry Control Module) 4 problems exist
1.B297B Driver Door Open Switch Circuit Not Plausible
2.U0073 CAN Bus Communication
3.U0140 Lost Communication with Body Control Module
4.U0155 Lost Communication with Instrument Cluster
PACM (Parking Assist Control Module) 6 problems exist
1.U0252 Lost Communication with Trailer Interface Control
Module
2.U0184 Lost Communication with Radio
3.B0956 Parking Assist Front Sensor Right Middle Circuit Incorrect Period
4.U0155 Lost Communication with Instrument Cluster
5.U0186 Lost Communication with Speaker Amplifier Module
6.U0140 Lost Communication with Body Control Module
SCLCM (Steering Column Lock Control Module) 4 problems exist
1.U0073 CAN Bus Communication
2.U0140 Lost Communication with Body Control Module
3.U0155 Lost Communication with Instrument Cluster
4.U0254 Lost Communication with Remote Start Module
The following systems are OK:
1.ECM (Engine Control Module)
2.RDCCM (Rear Differential Clutch Control Module)
3.DSCCM (Distance Sensing Cruise Control Module)
4.PBCM (Parking Brake Control Module)
5.MASM (Multi-Axis Acceleration Sensor Module)
6.PSCM (Power Steering Control Module)
7.SWASM (Steering Wheel Angle Sensor Module)
8.SCM (Suspension Control Module)
9.HCM (Headlamp Control Module)
10.HMICM (Human Machine Interface Control Module)
Could it be a bad battery? Battery voltage is 12.5V, running/charging is 14.9V.
Please can anyone help me with activation code for my launch x431 v+. I have my username and password and serial number but i have lost activation code. Can anyone help me to generate activation code from my serial number
hi guys, I have a seat ibiza 6j DCM3.7 in which the eprom was corrupted and I have no way of synchronizing the immobilizer with the dash, but I have the PIN and CS from the dash. Can anyone change the eprom so that it is synchronized? thank you
hello i have a problem whits VW ID4 2020 1ea959655EA TC233-32f
i do diagnostik on bench befor clear crash and i have DTC B2000 after clear crash this DTC B2000 remained can anyone help to clear this error B2000
Hi,
I need to clean C123EF0 from eeprom dump of Audi ABS unit. Maybe someone can help with cleaning it from dump, or has working dump to write and recode ?
any chance to have ori flash or full dump for above van. someone havent done to good job removing dpf and scr car underpowered smokes and such henve i want to revert it back to ori and see what happend. thanks in advance
![[Image: Screenshot-2025-01-27-174945.png]](https://i.ibb.co/cC9qHLQ/Screenshot-2025-01-27-174945.png)
