Hey guys i did a Stage 3 remap trying to achieve 2.4 bars of boost but i made a log and only achieved 2,1 bars of boost can someone take a look on the file? I don't know whats happening..
There is file and the log
Hello guys,
I've got Land Rover Sport L320 with TDV8 engine for air suspension repair, car arrived from another shop where guys tried to fix it, but without success. I fixed air suspension same day as car arrived, but we noticed that engine won't rev and it has faults in transmission, suspension and abs have DTC related to check DTC in ECU. car starts without faults, but if you leave it as is, without pressing accelerator pedal after engine start, few seconds engine is working rough, then check engine message on display shows and warning lights for transmission, suspension and abs lit up, engine doesn't want to accelerate anymore, but idling isn't rough anymore. only DTC in ECU when it occurs is: P0088-00 Fuel rail / system pressure - too high. But, if I press accelerator pedal at the same time when I crank the engine, engine revs up, car drives until you let it sit on idle.. I've changed fuel rail pressures sensor (found some replacement, OE comes with rail in package) and checked wiring to ECU, load tested all wires, all good. Playing around with that issue I've found out that when that DTC occurs, if I swap original FRP sensor for replacement, first 2 engine starts is ok, then in one point error comes back. I'm starting to suspect HPFP and injectors, but I want to be sure before condemning one of those 2, or both because it's an old car and customer doesn't want to spend lot's of money on it.
Any suggestions or solutions are welcome, I'm getting annoyed with it a little bit.
P.S. - customer only knew for air suspension problem, that's why car was towed to me, he didn't knew he has engine issues as well, but when we spoke about it, I have mentioned injectors, he said he did send them for reparation to one diesel specialist.
EDIT:
the issue is solved, changed fuel filter and fuel itself, diesel detoriated because car was parked for about 1 year...
I've been a long-time reader and finally decided to create an account.
I’m currently working on reprogramming a brand-new virgin UCH to a Renault Zoe PH2.
I’m using the reprogramming module from Asos, and it connects successfully to read the VIN and program other modules via SAE J2534 and a Bosch KTS590.
However, when attempting to reprogram the UCH, the module returns an error saying that it's not possible to program and that the SAE J2534 device is not connected, asking me to retry.
But I can read and can connect to receive identification numbers with KTS590 and RenCom.
Can gateway is unlocked.
What could be going wrong? I’ve already disabled the virus scanner and firewall on the PC.
Thanks in advance!
[font="MHH Font", Calibri, sans-serif]Hi all please can you help me i have a Fiat Delphi radio F250 and i need of the code the numbers on radio are :[/font]
[font="MHH Font", Calibri, sans-serif]7355333750[/font] [font="MHH Font", Calibri, sans-serif]HW VER 28315733 [/font] [font="MHH Font", Calibri, sans-serif]SW VER 05[/font] [font="MHH Font", Calibri, sans-serif]PROD DATE 3512[/font] [font="MHH Font", Calibri, sans-serif] SN 3750283157331224305248[/font]
Hello,
I have navi Europe 2013 on my vehicle. I would like to replace them with new ones, but I can't see the hdd sdd disk. No partitions are visible.
I tried in windows, linux but without success. I would also like to upload music. But the disk is only visible with the application that is in the vehicle. Please help. I am also paying for help.
good morning. wondering if anyone can help extract cs code from eeprom dump file? long story short lost wifes only key she had for the touareg eek!
i was able to extract pin code which oddly gave me 2 pin codes (03796/35754} vin/sn: vwz3z0e1376098 from eeprom dump bin. problem is i need also the skc code in order to program news keys.
i've attached dump bin. p.s i'm in the dog house with wife and would really appreciate any help with this lol.
Hello, could someone clarify for me if to do immo off on an EDC15C7 unit, with Bosch reference 0 281 010 346, which is installed in a Citroen Jumper 2.0hdi from 2002, I only have to modify the eeprom, or do I also have to do it with the flash.
Thank you very much
hello, i am currently looking for a damos for DL501 gen1 gearbox if someone have and are willing to share i would be greatful.
i am currently working on getting launch activated on this gearbox
Hello friends please I need help
I have vin not programmed fault but when i read eeprom i See vin is in the file
Please is IT possible to correct the file or make Immo off?
If anyone has a solution, I'm interested.
I support Programming when replacing a new Unit, used Unit for Toyota Lexus cars (SRS, EMPS, Engine, Transmisstion...)
If you want to do it quickly and reliably, please contact me via WhatsApp . I will help you faster.
PRICE : 100$ All model Toyota/ Lexus.
CAR INFORMATION:
Brand: COROLLA CROSS Year: 2023
Model code: MXGA15L-AHXEHA
Information on EPC:
TCM Part Number:
BEFORE: Many Warning light turn ON after new TCM Unit replaced
AFTER: All Warning light turn OFF
All services are in the attached txt file.
Please contact me via WhatsApp (informations find contact in my profile)
For urgent cases that you need to do immediately (ECU Security, Programming, 12 digit keycode...), if you send a message and there is no response, please call me. I will support within 5 minutes
Hello,
does anyone know the resistance that HV compressor should have between HV+ and HV-. I measured 40kOhm. The problem is that Xentry says it is not ok. But I measured two compressors and both have between 38 - 40kOhm and one works 100%. I have not problems with insulation.
Thanks
Pricing: 📌 1 Hour: $30 (Valid for up to 2 hours) • Includes SPS2 + Service Information (SI) + Unlimited VINs. ✅ Only vehicles manufactured in the USA are supported
📌 Full Day: $60 • Includes SPS2 + Service Information (SI) + Unlimited VINs. ✅ Only vehicles manufactured in the USA are supported
📌 7 Days: $100 • Includes SPS2 + Service Information (SI) + Unlimited VINs. ✅ Only vehicles manufactured in the USA are supported
📌 2 Hours (Unlimited VINs) (Works up to 3 hours): $53 ✅ Supports all VINs, including Korean and Australian vehicles • SPS2 only.
💳 Payment Method: ✅ PayPal (Goods and Services) for secure transactions.
Important Notes: ❌ No VPN required 📌 The account is linked to one computer only. ✅ Auto-login feature is available.
![[Image: qDuKhzk.jpeg]](https://i.imgur.com/qDuKhzk.jpeg)
![[Image: qd9k0Fe.jpeg]](https://i.imgur.com/qd9k0Fe.jpeg)
![[Image: CKkJ8YY.jpeg]](https://i.imgur.com/CKkJ8YY.jpeg)
![[Image: tfhEckf.jpeg]](https://i.imgur.com/tfhEckf.jpeg)
![[Image: IIPlibT.jpeg]](https://i.imgur.com/IIPlibT.jpeg)
![[Image: ecu-opel-0281014449-666x500.jpg.webp]](https://www.ecubackup.com/wp-content/uploads/2023/07/ecu-opel-0281014449.jpg)
![[Image: 2025-01-25-072405.png]](https://i.ibb.co/bXcZqq8/2025-01-25-072405.png)
![[Image: 2025-01-25-072429.png]](https://i.ibb.co/5cpFbKk/2025-01-25-072429.png)
![[Image: 2025-01-25-072459.png]](https://i.ibb.co/Y8vwX0Q/2025-01-25-072459.png)
![[Image: 2025-01-25-072831.png]](https://i.ibb.co/w0HxQnv/2025-01-25-072831.png)
![[Image: 2025-01-25-072530.png]](https://i.ibb.co/VVL5pFG/2025-01-25-072530.png)