Hello friends. I need the pinout diagram of the ECU written below. It would be better if I could find the PCB diagram and flash file. Can you help me with this?
Hi Guys
I need some advice from more experienced people.
W207 2009 e coupe. One day it didnt start. Just like that.
No start
No reaction on inserting a key to ignition
No remore central locking ( not work either)
When i insett different key (belong to other car) then and only then its showing on dash that key is from different car.
Steering lock been done 5 months ago. (Motor change). Right now there is not even relay click.
Diagmostics (eis/ezs) in authorisations shows the key is not valid.
So local locksmith made a new key on the table from eis. But same thing. Key not valid but new key trying to initialise itself. And red light on key stays on for a while when inserted to eis.
After 2h in ignition still didnt initialise.
I have simon touch mb clinic lite and nec full but never used it. But now i was able to read a be key eprom to check last two bytes of new key. Was 04FC - not activated. So i changed it to 14EC as some thread here suggested. No change. Key not working at all.
Any suggestion where is the problem? Is ot EIS? Am I right thinking that?
And if yes is cloning eis good idea or the data might be corrupted and different route should be taken. Any advice appreciated.
I tried flashing my cluster to the Silver Design, but unfortunately, it shows me this error does anyone have a solution for this problem?
It worked without any issues on the Comand.
Hello,
Could somebody please transfer immo data and VIN from OLD to NEW ?
All ecus are EDC17CP24 from V12 TDI Audi Q7, same engine code CCGA.
Thank you very much, all files are attached and marked.
Hi everyone, I would like to sell my obdstar x300dp plus yellow version C full, with all the accessories, the device and new used. Only 2 times. one for the km and one for the key, I have other tools and I prefer to sell it rather than leave it still, it still has the film on the display and the accessories in the original, never opened, sealed bag. I'm asking for €1000. If anyone is interested, contact me, have a good evening
Hello everybody!
Can you tell me if the SAM OLD module and DONOR are compatible? I.ve tried to directly connect it but it does not work. please tel me how I have to proceed!
Hello. I'm searching for virgin eeprom file for edc16cp33 nissan x-trail. Or I need help with virginize my file. My eeprom was corrupt when i program flash witch kess by obd. Now car don't start. In attatchment ory corrupt and good from another ECU eeprom dump.
Hello guys, im looking for someone who can help me a bit with tunerstudio for some settings etc, i'd like to validate that i have set up my injector deadtimes correctly, and someone who knows better than me since its my first time to sanity check my ignition advance table, engine is on bench and starts very fast, but my idle fluctuates a lot, i have stepper motor idle that works okay, but when i set engine close to 800-900 rpm it stalls after a bit, if anyone can help i will send you tunerstudio file via pm. Thanks!!
Hi friends, i am trying to find id from new tpms sensor on 2014 cherokee, i dont have tpms tool but my autel allows me to manually enter id which im supposed to read from sensor it self but i cant figure out which one is the id, please check photos. One is sensor it self and what computer shows for ids i cant seem to find anything similar on sensor. Please help me out
I have a problem with my 2022 Infiniti q50 infotainment dual screens that the upper screen doesn’t save the brightness when I shut off the car and start it again the brightness resets to the middle of the brightness dial the lower screen saves the brightness and that’s very annoying especially when driving in late night I have searched for the solution and found out that there is an update that some dealers in USA do only if you give them a reasonable reason and I found out that there is a service bulletin about updating the Infiniti screens but the problem is that asist software is needed can any one help me with to get the files.
My car is a 2022 Infiniti Q50 GCC specs.
Attached is a link to the service bulletin.
Thanks to all.
While I was surfing the web I’ve seen a Chevy equinox with some pages in the cluster (like transmission fluid temp page and other pages) that I don’t have I have searched in the infotainment screen if they are there and can be enabled so I can see them in the cluster but I didn’t find them so I contacted the man who posted the image and asked him how he did it he said through programming but did not specify how does any one know how?
I have 2 j2534 VCIs one is VCX SE that doesn’t support CAN FD and I have maxiflash vci200 which supports CAN FD.
I have a BMW e92 320D 2009 that doesn't want to start (crank, no start). Starting issues started a while ago and the problem got worse as time went on. Sometimes it would start on first try then on any random attempt. Few days ago car started on first try on its own for the last time and then wouldn't anymore. Then I have used booster cables to get it going again and it did start, but any further attempts with or without booster cables failed.
checked all fuses and all appear fine
tried battery from different BMW with exact same battery and no start issues
fully charged this cars battery
disconnected maf sensor and tried starting, didnt help
replaced the DDE relay with brand new one
no communication with ECU, but ECU itself seems fine
car has been driven with no front underbody cover for a while
when the key gets inserted into the key slot and the ignition turned on (all electronics on) the fuel pump starts going by itself.
when attempting to start the car the 3 dashboard warnings lights appear (see image below or video at the end)
[*]
I would be very thankful if someone could share wiring diagrams with me for this model.
Has anyone used AVDI FR010 - PATS INITIALIZATION (2014+)? I’m looking for real user feedback – does the license work 100% reliably? Are there any limitations or specific conditions to be aware of?
![[Image: 2LISj7n.md.jpg]](https://iili.io/2LISj7n.md.jpg)
![[Image: 2LIShdX.md.jpg]](https://iili.io/2LIShdX.md.jpg)
